Firstech, LLC. P2W900FMR Manuel D’Utilisation
14
Adjusting the shock sensor sensitivity is done at the actual sensor, which is generally mounted
somewhere under the vehicle’s dashboard. The higher the number on the dial means greater sensitivity
to impact. The recommended dial setting for most vehicles is somewhere between 2 & 4. If you are
testing your sensor, please note that the shock sensor does not recognize impact for 30 seconds after
the system has been armed.
somewhere under the vehicle’s dashboard. The higher the number on the dial means greater sensitivity
to impact. The recommended dial setting for most vehicles is somewhere between 2 & 4. If you are
testing your sensor, please note that the shock sensor does not recognize impact for 30 seconds after
the system has been armed.
Advanced System Functions
The following section reviews advanced system functions. Many of these functions require multiple
steps or additional programming by your local authorized CompuStar dealer to be active.
Drive Lock/Ignition Controlled Door Locks
Tap buttons (I+IV) simultaneously for 0.5 seconds to turn on and off drive lock (also known as
ignition controlled door locks). The remote will beep once and the drive lock icon will
illuminate to confirm that drive lock mode is activated. The remote will beep twice and the drive lock icon
will disappear to confirm drive lock is off.
IMPORTANT: Drive lock mode requires that the dealer turn on Option 1-9. Drive lock has two settings;
Default 1: Off
Option 2: Locks the doors when the ignition is on and after the brake is depressed.
Option 3: locks the doors when the RPM’s have reached two times that of idle speed (this setting
requires that a tachometer wire is connected).
With both settings, the doors will unlock when the ignition is turned off. If using this feature on a manual
transmission vehicle, the doors will unlock upon setting the emergency / parking brake.
ignition controlled door locks). The remote will beep once and the drive lock icon will
illuminate to confirm that drive lock mode is activated. The remote will beep twice and the drive lock icon
will disappear to confirm drive lock is off.
IMPORTANT: Drive lock mode requires that the dealer turn on Option 1-9. Drive lock has two settings;
Default 1: Off
Option 2: Locks the doors when the ignition is on and after the brake is depressed.
Option 3: locks the doors when the RPM’s have reached two times that of idle speed (this setting
requires that a tachometer wire is connected).
With both settings, the doors will unlock when the ignition is turned off. If using this feature on a manual
transmission vehicle, the doors will unlock upon setting the emergency / parking brake.
Turbo Timer Mode
The built-in turbo timer keeps the vehicles engine running for either 1, 2 or 4 minutes
(programmable from dealer with Option 2-2) after the vehicle key has been removed from the
ignition. This feature will keep oil running through the turbo system to allow for appropriate
cooling time. Tap buttons (III+IV) simultaneously for 0.5 seconds to turn on or off turbo mode.
The remote will beep once and the turbo icon will illuminate to confirm that turbo mode is activated. The
remote will beep twice and icon will disappear to confirm turbo mode is off.
IMPORTANT: To utilize this feature, the emergency / parking brake wire must be connected to the
CompuStar system. Consult your local authorized CompuStar dealer for installation.
(programmable from dealer with Option 2-2) after the vehicle key has been removed from the
ignition. This feature will keep oil running through the turbo system to allow for appropriate
cooling time. Tap buttons (III+IV) simultaneously for 0.5 seconds to turn on or off turbo mode.
The remote will beep once and the turbo icon will illuminate to confirm that turbo mode is activated. The
remote will beep twice and icon will disappear to confirm turbo mode is off.
IMPORTANT: To utilize this feature, the emergency / parking brake wire must be connected to the
CompuStar system. Consult your local authorized CompuStar dealer for installation.
2
nd
Car Mode (Multiple Vehicle Control)
The P2W9000FM remotes have the ability to operate a 2
nd
vehicle. Press buttons (III+IV)
simultaneously for 2.5 seconds to turn on or off 2
nd
car mode. The remote will beep once and
the 2
nd
car icon will illuminate to confirm that 2
nd
car mode is activated. The remote will beep
twice and the icon will disappear to confirm 2
nd
car mode is off.
IMPORTANT: 2
nd
car mode requires the remote to be programmed to a 2
nd
vehicle that is equipped with
either a P2W9000FM-AS, P2W9000FM-A or P2W9000FM-S, P2WSS-AS, P2WSS-A or P2WSS-S.
Remote Alarm Clock
All CompuStar PRO two-way LCD remotes have a built-in alarm clock. This alarm clock feature is similar
to ordinary alarm clocks in that the remote (not the car) will beep at a programmed timed. To program
the alarm clock perform the followings steps;
to ordinary alarm clocks in that the remote (not the car) will beep at a programmed timed. To program
the alarm clock perform the followings steps;