HoMedics MYB-W20 Manuel D'Instructions
2
3
IMPORTANT:
To avoid accidental dispensing of liquid, slide the Dispensing Control Switch to [OFF]
and install batteries before filling the Sanitizer Reservoir.
and install batteries before filling the Sanitizer Reservoir.
How To Install Batteries:
Press the [OPEN] release button on the underside of the unit to open the Battery/Control
Compartment door. Insert three (3) AA alkaline batteries carefully following the polarity
(+ / –) markings shown inside the battery compartment. Note: when the batteries are low
and need replacing, the red LED Low Battery Indicator will flash for 10 seconds after each
dispensing cycle.
Compartment door. Insert three (3) AA alkaline batteries carefully following the polarity
(+ / –) markings shown inside the battery compartment. Note: when the batteries are low
and need replacing, the red LED Low Battery Indicator will flash for 10 seconds after each
dispensing cycle.
Congratulations!
Thank you for purchasing the MyBaby, by HoMedics Hand Sanitizer.
The Hands Sanitizer is one of the most advanced products of its kind.
Luxury meets practicality and hygiene meets style:
- Motion sensor technology provides sanitary hands-free
operation.
- Adjustable controller dispenses the right amount of sanitizer or
gel every time.
- Convenient magnetically attached drip tray removes easily for
cleaning.
- Elegant functional design makes sanitizing a pleasure.
The Hands Sanitizer is one of the most advanced products of its kind.
Luxury meets practicality and hygiene meets style:
- Motion sensor technology provides sanitary hands-free
operation.
- Adjustable controller dispenses the right amount of sanitizer or
gel every time.
- Convenient magnetically attached drip tray removes easily for
cleaning.
- Elegant functional design makes sanitizing a pleasure.
How To Use
1. Lift the cover to the Sanitizer Reservoir and fill up to the “Max” line with any
brand of liquid soap or sanitizer. Do not overfill as this may cause dripping.
Replace the plug in the sanitizer reservoir securely.
Replace the plug in the sanitizer reservoir securely.
2. Press the [OPEN] release button to open the Battery & Control Compartment
on the bottom of the unit and slide the Dispenser Control Switch from [OFF]
to your desired amount of soap to be dispensed [1 = LOW], [2 = MEDIUM]
or [3 = HI]. The Red LED will turn on for 12 seconds. During this period, the
Motion Sensor and motor will not function. This will allow enough time to
close the Battery & Control Compartment door and position the unit without
triggering the Motion Sensor.
to your desired amount of soap to be dispensed [1 = LOW], [2 = MEDIUM]
or [3 = HI]. The Red LED will turn on for 12 seconds. During this period, the
Motion Sensor and motor will not function. This will allow enough time to
close the Battery & Control Compartment door and position the unit without
triggering the Motion Sensor.
3. Attach the Drip Tray as shown. Magnets help hold in place.
4. Place your hand under the spout to activate the Motion Sensor. The Hand
4. Place your hand under the spout to activate the Motion Sensor. The Hand
Sanitizer will then dispense liquid.
Caution: All
servicing of
this product
must be
performed by
authorized
HoMedics
Service
Personnel
only.
CLEAN
Function
ON/OFF
Switch
Dispenser Control
Switch for Amount
of Sanitizer:
OFF/
1–LOW
2–MEDIUM
3–HIGH
Switch for Amount
of Sanitizer:
OFF/
1–LOW
2–MEDIUM
3–HIGH
Door Release
for Battery
and Control
Compartment
Spout
Drip Tray
Sanitizer Reservoir
Motion
Sensor
Sensor
Red LED:
Indicates Motion
Sensor OFF During
Set-up; Flashes to
Indicate Low Battery
Condition
Indicates Motion
Sensor OFF During
Set-up; Flashes to
Indicate Low Battery
Condition
Figure 1
Figure 2