HoMedics MYB-W20 Manuel D'Instructions
5
4
How to use the CLEAN Function: If you wish to change the type of liquid in Hand Sanitizer, you may
use the CLEAN function to empty and clean the unit. Press the [CLEAN] button and the unit will enter
the auto cleaning mode: 1.) first the Red LED will illuminate for 12 seconds to allow you to replace the
battery door and position the unit for cleaning, 2.) then the motor will turn on and pump for 30 seconds.
During this period, you can press the [CLEAN] button again to abort the cleaning function (motor will
turn off). The CLEAN function will work with the Dispenser Control Switch set to [1], [2] or [3]; it will not
work with the Dispenser Switch in the OFF position. Repeat until there is no more liquid in the reservoir.
To thoroughly flush out the unit, you should add water to the reservoir and repeat the cleaning process.
use the CLEAN function to empty and clean the unit. Press the [CLEAN] button and the unit will enter
the auto cleaning mode: 1.) first the Red LED will illuminate for 12 seconds to allow you to replace the
battery door and position the unit for cleaning, 2.) then the motor will turn on and pump for 30 seconds.
During this period, you can press the [CLEAN] button again to abort the cleaning function (motor will
turn off). The CLEAN function will work with the Dispenser Control Switch set to [1], [2] or [3]; it will not
work with the Dispenser Switch in the OFF position. Repeat until there is no more liquid in the reservoir.
To thoroughly flush out the unit, you should add water to the reservoir and repeat the cleaning process.
IMPORTANT:
1. The Motion Detector that activates dispensing uses a sensitive infrared sensor. To avoid accidental
dispensing of liquid, please do not place Hand Sanitizer Dispenser in direct sunlight.
2. After a period of inactivity, the sanitizer inside Hand Sanitizer Dispenser may become dry and clog
the line. Should this occur, simply use a toothpick or water to remove the obstruction.
3. The only part of the Hand Sanitizer designed to be wet is the liquid reservoir and spout. Do not
immerse the Hand Sanitizer in water as the product will be damaged.
4. Run the Clean function to flush the sanitizer reservoir with water, then remove the batteries from the
battery compartment whenever the Hand Sanitizer is to be left unused for a long period of time.
5. To clean the unit, use a soft damp cloth. Do not clean with a abrasive materials or corrosive
substances.
dispensing of liquid, please do not place Hand Sanitizer Dispenser in direct sunlight.
2. After a period of inactivity, the sanitizer inside Hand Sanitizer Dispenser may become dry and clog
the line. Should this occur, simply use a toothpick or water to remove the obstruction.
3. The only part of the Hand Sanitizer designed to be wet is the liquid reservoir and spout. Do not
immerse the Hand Sanitizer in water as the product will be damaged.
4. Run the Clean function to flush the sanitizer reservoir with water, then remove the batteries from the
battery compartment whenever the Hand Sanitizer is to be left unused for a long period of time.
5. To clean the unit, use a soft damp cloth. Do not clean with a abrasive materials or corrosive
substances.
Trouble Shooting:
No Sanitizer Dispensed; Motor Does Not Run
1. Ensure that Dispensing Control Switch is turned ON in the 1 = LOW; 2 = MEDIUM or
3 = HI position; not OFF.
2. Hands are placed directly between the Motion Sensor and Spout.
3. Ensure unit is not placed in bright sunlight which will interfere with Motion Sensor operation.
4. Batteries are installed with correct polarity (+/ –) and not dead.
3 = HI position; not OFF.
2. Hands are placed directly between the Motion Sensor and Spout.
3. Ensure unit is not placed in bright sunlight which will interfere with Motion Sensor operation.
4. Batteries are installed with correct polarity (+/ –) and not dead.
No Sanitizer Dispensed; Motor Runs
1. During start-up you may need to activate the Motion Sensor several times to “prime” the pump to
begin dispensing sanitizer.
2. The sanitizer reservoir should be at least ¼ FULL.
3. Make sure that no dried sanitizer is clogging the spout or pump tubing. Use a toothpick to
clean the spout. If necessary, empty the sanitizer tank, fill with water and run the CLEAN
Function.
begin dispensing sanitizer.
2. The sanitizer reservoir should be at least ¼ FULL.
3. Make sure that no dried sanitizer is clogging the spout or pump tubing. Use a toothpick to
clean the spout. If necessary, empty the sanitizer tank, fill with water and run the CLEAN
Function.
Battery Precautions:
1. Use AA alkaline batteries only. Do not use rechargeable batteries.
2. Replace all batteries at the same time.
3. Clean the battery contacts and the contacts of the device prior to battery installation with a dry cloth.
4. Ensure the batteries are installed correctly with regard to polarity (+ /–).
5. Remove batteries from the unit when it is not to be used for an extended period of time.
6. Remove depleted batteries from the unit promptly. Dispose of used batteries safely. Keep all
batteries away from children. Batteries are small objects and could be ingested. If swallowed,
contact a physician at once. Do not open batteries or dispose of in fire. Do not mix the new and
used batteries.
WARNING
Keep out of reach of children. When using liquid sanitizer, avoid contact with eyes. In case of eye
contact, flush with water. If swallowed get medical help or contact Poison Control Center right away.
contact, flush with water. If swallowed get medical help or contact Poison Control Center right away.