Monogram ZWE23ESHSS Manuel De Montage

A. Reinstall center hinge first and torque the screws 

to 65 in-lbs. With the LH door at 90º to the front ofthe 
case, lower the refrigerator door onto the center 
hinge. Ensure that the door and hinge align correctly. 

B. Rotate door closed and make sure moveable center 

sealing portion of the door aligns with the striker. If 
the door will not self-close after reinstalling, remove 
door, turn door upside down, check alignment mark 
and arrow; (there is an alignment mark on the door 
closure mechanism It corresponds to an alignment 
mark on the bottom end cap. Rotate door closure 
mechanism to align mark and arrow, reinstall door).

C. Be sure to reinstall the ground wire and strain relief 

to the top hinge.

D. Reinstall the hinge cover. Note: Ensure wires are not 

pinched or under screw bosses before tightening 
screws.

E. Follow the same procedure on the opposite door. 

Recommended copper water supply kits are WX8X2, WX8X3 

or WX8X4, depending on the amount of tubing you need. 

Approved plastic water supply lines are GE SmartConnect™ 

Refrigerator Tubing (WX08X10006, WX08X10015 and 

WX08X10025).
When connecting your refrigerator to a GE Reverse Osmosis 

Water System, the only approved installation is with a GE 

RVKit. For other reverse osmosis water systems, follow the 

manufacturer’s recommendations. 
If the water supply to the refrigerator is from a Reverse 

Osmosis Water Filtration System (RO)AND the refrigerator 

also has a water filter, use the refrigerator’s filter bypass 

plug. Using the refrigerator’s water filtration cartridge in 

conjunction with an RO water filter can result in hollow ice 

cubes.
This water line installation is not warranted by the 

refrigerator or ice maker manufacturer. Follow these 

instructions carefully to minimize the risk of expensive 

water damage.
Water hammer (water banging in the pipes) in house 

plumbing can cause damage to refrigerator parts and 

lead to water leakage or flooding. Call a qualified plumber 

to correct water hammer before installing the water 

supply line to the refrigerator.
To prevent burns and product damage, do not hook up 

the water line to the hot water line.
Do not install the ice maker tubing in areas where 

temperatures fall below freezing.
When using any electrical device (such as a power drill) 

during installation, be sure the device is double insulated 

or grounded in a manner to prevent the hazard of electric 

shock, or is battery powered.
All installations must be in accordance with local 

plumbing code requirements.
•  Copper or GE SmartConnect™ Refrigerator Tubing kit, 

1/4” outer diameter to connect the refrigerator to the 

water supply. If using copper, be sure both ends of the 

tubing are cut square.

To determine how much tubing you need:  

measure the distance from the water valve on the back of 

the refrigerator to the water supply pipe. Be sure there is 

sufficient extra tubing to allow the refrigerator to move out 

from the wall after installation.
GE SmartConnect™ Refrigerator Tubing Kits are available 

in the following lengths:
6’ (1.8 m) 

– WX08X10006

15’ (4.6 m) 

– WX08X10015

25’ (7.6 m) 

– WX08X10025

align marks

Underside OF
Fresh Food Door

1. If space or model limits opening door to less than 180°, then:

     a) Remove door, carefully turn door upside down.

     b) Check alignment of door closure mechanism shaft on

         underside of door. The flats on the shaft should  

         correspond to alignment tab on plastic ring or mark 

         on bottom end cap.

     c) If shaft is not aligned to tab/mark, using 5/32” Allen  

         wrench, rotate door closure mechanism shaft  

         counterclockwise for right door and clockwise for left  

         door. Then align flat with tab/mark.

     d) Install the door at 90°.