Toshiba DVR620KC Manuel D’Utilisation

This unit records the programs according to priority if the timer programmings are overlapped. The timer
programming set previously has priority.
A timer recording of lower priority will be canceled or start from the middle.
Check the overlapped timer programmings and change the priority if necessary.

•  If there is a power failure or this unit has been 

unplugged for more than 30 seconds, the clock setting
and all timer programming will be lost.

•  If a disc is not inserted or if a inserted disc is not

recordable (finalized DVD-RW/-R, finalized DVD+RW, a
fully recorded disc, etc.), “DVD” on the front panel
display flashes and timer recording cannot be
performed. In some cases,

will appear momentarily

around the start point as the unit attempts to record.
Please insert a recordable disc.

•  If a cassette tape with an erase-protection tab is not in 

the cassette compartment or there is no cassette tape in 
the cassette compartment, “VCR” on the front panel
display flashes and timer recording cannot be
performed. Please insert a recordable cassette tape.

•  If you press

[TIMER SET] and turn on the unit while 

either DVD or VCR is in timer standby mode,
disappears. In this case, you cannot change the mode
between DVD and VCR. You cannot change any settings
using [SETUP] or edit discs.

•  When all the timer recording is completed,

flashes. To

play back or eject the recorded disc, press 
[I/

y

y ON/STANDBY] first, then select the recorded title and 

press [PLAY 

B], or [OPEN/CLOSE A] to remove the disc.

•  During timer recording or timer standby mode (

will

appear), any operations on the unit will not be available.
To make these operations available, press [STOP

C] to

stop the timer recording or [TIMER SET] to cancel timer 
standby mode (

will disappear).

•  To cancel the timer standby mode, press [TIMER SET].
•  When the starting and the ending time are the same, 

“Exceeds 12 hours” appears and the program setting will
not be accepted.

•  When the programmed starting and ending time are 

earlier than the current time, the setting will not be
accepted.

•  If the starting time is earlier and the ending time is later

than the current time, the recording will start right after
[TIMER SET] is pressed.

•  The timer recording cannot be performed in DVD and

VCR at the same time. If you set 2 programming with the 
same channel and time in both devices, the program
with a lower program number will be recorded.

•  “Press TIMER SET for timer recording” will appear on the TV 

screen 5 minutes before the programmed starting time.

• When the recording time of 2 programs are overlapped, or 

the end time of a program and the start time of another 
program is the same, the first 2 minutes (at the longest) of the
subsequent program will be cut off.

• If the cut-off portion comes up to 3 minutes or more, this

program will be displayed with errors number E40 in the
timer programming list.

  A program that has earlier start time has priority.

  A program set previously (PROG. A) has priority.

The first 2 minutes (at the longest) will be cut off.

The first 2 minutes (at the longest) will be cut off.

 PROG. A will start after PROG. B is complete to be
recorded.

  

PROG.A will not be recorded.

The first 2 minutes (at the longest) will be cut off.

currently being recorded and the start time
of the subsequent program are same:
The beginning of the PROG. B may be cut off.

The first 2 minutes (at the longest) will be cut off.

E9PKCCD_DVR620KC_EN_book.indb   42

E9PKCCD_DVR620KC_EN_book.indb   42

2011/09/01   9:29:16

2011/09/01   9:29:16