Manuels d'utilisation pour Topcon Marine Instruments GPT-2000

Table des matières

• TopCover

  1
• FOREWORD

  3
  • General Handling Precautions

    4
  • Display for Safe Use

    5
  • Safety Cautions

    5
  • User

    6
  • Exceptions from Responsibility

    6
  • Safety Standard for Laser Beam

    7
  • Safety Standard for Laser Beam

    7
  • Labels

    7
  • Symbol mark while the laser is emitting.

    7
  • Contents

    8
  • Standard Set Composition

    11
• 1 NOMENCLATURE AND FUNCTIONS

  12
  • 1.1 Nomenclature

    12
  • 1.2 Display

    14
  • 1.3 Operating Key

    15
  • 1.4 Function Key (Soft Key)

    15
  • 1.5 Serial signal RS-232C connector

    17
• 2 PREPARATION FOR MEASUREMENT

  18
  • 2.1 Power Connection

    18
  • 2.2 Setting Instrument Up For Measurement

    19
  • 2.3 Power Switch Key ON

    20
  • 2.4 Battery Power Remaining Display

    21
  • 2.5 Vertical and Horizontal Angle Tilt Correction

    22
  • 2.6 How to Enter Alphanumeric characters

    24
  • 2.7 Point Guide (Only for Point Guide type)

    25
  • 2.8 Laser Plummet ON/OFF (Only for Laser Plummet type)

    26
• 3 ANGLE MEASUREMENT

  27
  • 3.1 Measuring Horizontal Angle Right and Vertical Angle

    27
  • 3.2 Switching Horizontal Angle Right/Left

    28
  • 3.3 Measuring from the Required Horizontal Angle

    28
    • 3.3.1 Setting by Holding the Angle

      28
    • 3.3.2 Setting a Horizontal Angle from the Keys

      29
  • 3.4 Vertical Angle Percent Grade(%) Mode

    29
  • 3.5 Repetition Angle Measurement

    30
  • 3.6 Buzzer Sounding for Horizontal Angle 90° Increments

    31
  • 3.7 Compasses ( vertical angle)

    32
• 4 DISTANCE MEASUREMENT

  33
  • 4.1 Setting of the Atmospheric Correction

    33
  • 4.2 Setting of the Correction for Prism Constant / Non-prism Constant

    33
  • 4.3 Distance Measurement (Continuous Measurement)

    34
  • 4.4 Distance Measurement (N-time Measurement/Single Measurement)

    35
  • 4.5 Fine Mode/Tracking Mode/Coarse Mode

    36
  • 4.6 Stake Out (S.O)

    37
  • 4.7 Offset Measurement

    38
    • 4.7.1 Angle Offset

      39
    • 4.7.2 Distance Offset Measurement

      41
    • 4.7.3 Plane Offset Measurement

      43
    • 4.7.4 Column Offset Measurement

      45
• 5 COORDINATE MEASUREMENT

  47
  • 5.1 Setting Coordinate Values of Occupied Point

    47
  • 5.2 Setting Height of the Instrument

    48
  • 5.3 Setting Height of Target (Prism Height)

    48
  • 5.4 Execution of Coordinate Measuring

    49
• 6 SPECIAL MODE (Menu Mode)

  50
  • 6.1 Application Measurement (PROGRAMS)

    51
    • 6.1.1 Remote Elevation measurement (REM)

      51
    • 6.1.2 Missing Line Measurement (MLM)

      54
    • 6.1.3 Setting Z Coordinate of Occupied Point

      57
    • 6.1.4 Area Calculation

      60
    • 6.1.5 Point to Line Measurement

      63
  • 6.2 Setting the GRID FACTOR

    65
  • 6.3 Setting Illumination of Display and Cross Hairs

    66
  • 6.4 Setting Mode 1

    67
    • 6.4.1 Setting Minimum Reading

      67
    • 6.4.2 Auto Power Off

      68
    • 6.4.3 Vertical and Horizontal Angle Tilt correction ( Tilt ON/OFF)

      69
    • 6.4.4 Systematic Error of Instrument Correction (only for GPT-2003/2005/2006)

      69
    • 6.4.5 Selecting Battery Type

      70
  • 6.5 Setting Contrast of Display

    70
• 7 DATA COLLECTION

  71
  • 7.1 Preparation

    73
    • 7.1.1 Selecting a File for Data Collection

      73
    • 7.1.2 Selecting a Coordinate File for Data Collection

      74
    • 7.1.3 Occupied Point and Backsight Point

      74
  • 7.2 Operational Procedure of “DATA COLLECT”

    77
    • 7.2.1 Searching the recorded data

      78
    • 7.2.2 Entering PCODE / ID using PCODE Library

      78
    • 7.2.3 Entering PCODE / ID from the list of PCODE

      79
  • 7.3 Data Collect Offset Measurement mode

    80
    • 7.3.1 Angle Offset Measurement

      80
    • 7.3.2 Distance Offset Measurement

      82
    • 7.3.3 Plane Offset Measurement

      84
    • 7.3.4 Column Offset Measurement

      86
  • 7.4 NEZ Auto Calculation

    87
  • 7.5 Editing PCODE Library [PCODE INPUT]

    88
  • 7.6 Setting Parameter of Data Collect [CONFIG.]

    89
• 8 LAYOUT

  90
  • 8.1 Preparation

    92
    • 8.1.1 Setting the GRID FACTOR

      92
    • 8.1.2 Selecting Coordinate Data File

      93
    • 8.1.3 Setting Occupied Point

      94
    • 8.1.4 Setting Backsight Point

      96
  • 8.2 Executing a Layout

    98
  • 8.3 Setting a New Point

    100
    • 8.3.1 Side Shot Method

      100
    • 8.3.2 Resection Method

      102
• 9 MEMORY MANAGER MODE

  106
  • 9.1 Display Internal Memory Status

    107
  • 9.2 Searching Data

    108
    • 9.2.1 Measured Data Searching

      108
    • 9.2.2 Coordinate Data Searching

      110
    • 9.2.3 PCODE LIBRARY Searching

      111
  • 9.3 FILE MAINTENANCE

    112
    • 9.3.1 Rename a File

      113
    • 9.3.2 Searching Data in a File

      113
    • 9.3.3 Deleting a File

      114
  • 9.4 Coordinate Data Direct Key Input

    115
  • 9.5 Delete a Coordinate Data from a File

    116
  • 9.6 Editing PCODE Library

    117
  • 9.7 Data Communications

    118
    • 9.7.1 Sending Data

      118
    • 9.7.2 Loading Data

      119
    • 9.7.3 Setting Parameter of Data Communications

      120
  • 9.8 Initialization

    121
• 10 SET AUDIO MODE

  122
• 11 SETTING THE PRISM / NON-PRISM CONSTANT VALUE

  123
• 12 SETTING ATMOSPHERIC CORRECTION

  124
  • 12.1 Calculation of Atmospheric Correction

    124
  • 12.2 Setting of Atmospheric Correction Value

    124
• 13 CORRECTION FOR REFRACTION AND EARTH CURVATURE

  129
  • 13.1 Distance Calculation Formula

    129
• 14 POWER SOURCE AND CHARGING

  130
  • 14.1 On-board Battery BT-52QA

    130
• 15 DETACH/ATTACH OF TRIBRACH

  132
• 16 SELECTING MODE

  133
  • 16.1 Items of the Selecting Mode

    133
  • 16.2 How to Set Selecting Mode

    135
• 17 CHECK AND ADJUSTMENT

  137
  • 17.1 Checking and adjusting of instrument constant

    137
    • 17.1.1 Checking of the accuracy of the non-prism mode

      137
  • 17.2 Checking the Optical Axis

    138
  • 17.3 Checking/Adjusting the Theodolite Functions

    140
    • 17.3.1 Checking /Adjusting the Plate Level

      141
    • 17.3.2 Checking /Adjusting the Circular Level

      141
    • 17.3.3 Adjustment of the Vertical Cross-hair

      142
    • 17.3.4 Collimation of the Instrument

      143
    • 17.3.5 Checking / Adjusting the Optical Plummet Telescope

      144
    • 17.3.6 Checking / Adjusting the Laser Plummet (For Laser Plummet type)

      145
    • 17.3.7 Adjustment of Vertical Angle 0 Datum

      146
  • 17.4 How to Set the Instrument Constant Value

    147
  • 17.5 Adjustment of Compensation Systematic Error of Instrument

    148
• 18 PRECAUTIONS

  150
• 19 SPECIAL ACCESSORIES

  151
• 20 BATTERY SYSTEM

  154
• 21 PRISM SYSTEM

  155
• 22 ERROR DISPLAYS

  156
• 23 SPECIFICATIONS

  158
• APPENDIX

  161
• LastCover

  168