Epson CX11N Descrizione Prodotto

Epson AcuLaser CX11N/CX11NF

8/05

Epson AcuLaser CX11N/CX11NF

 - 

11

When you see the following messages in the LCD screen or in 
the EPSON Status Monitor 3 window, you need to replace 
the indicated unit. You can continue printing for a short time 
after a message appears, but Epson recommends replacement 
to maintain print quality and extend the life of your product. 

Note: 
To clear the message, press the 

Setup button on the control 

panel, select Reset from Printer settings, then select Clear All 
Warnings.

The CX11N stops printing if the worn consumable might damage the 
CX11N. You must replace the consumable product to continue.

If a consumable product reaches the end of its service life, the 
product stops printing and displays the following messages on 
the LCD screen or in the EPSON Status Monitor 3 window. 

1

The letters C, M, Y, and K appear in this position, indicating the 
color of the empty toner cartridge.

2  Even if this message is displayed in the LCD screen, you can 

continue to print for a short time by pressing the 

x

B&W Start or 

x

Color Start button on the control panel. The message in the 

LCD screen changes from Replace Photocondctr to Worn 
Photoconductor.

Messages appear for one consumable product at a time. After 
replacing a part, check the LCD screen for replacement 
messages for other parts.

When a toner cartridge is empty, a message appears on the 
LCD screen indicating which toner cartridge needs to be 
replaced. If you are going to print a large document or make a 
large number of copies and one of the toner cartridges is low, 
you can change that cartridge so you won’t run out of toner in 
the middle of the job. See: 
❏ “Changing a Low Toner Cartridge” (next column)
❏ “Removing and Replacing a Toner Cartridge” on page 12 

Always follow these precautions when replacing a toner 
cartridge: 
❏ Install a genuine Epson toner cartridge. Using a non-Epson 

toner cartridge may affect print quality. Other products 
may cause damage to your printer not covered by Epson’s 
warranty.

❏ When handling toner cartridges, always place them on a 

clean smooth surface.

❏ If you move a toner cartridge from a cool to a warm 

environment, wait for at least one hour before installing it 
to prevent damage from condensation.

Warning: 
Do not touch the toner and keep it away from your eyes. If toner gets 
on your skin or clothes, wash it off with soap and water immediately.

❏

Keep toner cartridges out of the reach of children.

❏

Do not dispose of toner cartridges in fire, as they may explode 
and cause injury. Dispose of them according to local 
regulations.

❏

If toner spills, use a broom and dustpan or a damp cloth with 
soap and water to clean it up. Because the fine particles can 
cause a fire or explosion if they come into contact with a 
spark, do not use a vacuum cleaner.

1. Make sure the CX11N is turned on, then press the 

Setup

 button.

The Setup light turns on and the LCD screen displays 

Setup Mode

 for a few seconds, then changes to the Setup 

menu screen.

2. Use the u or d button to select 

Printer Settings

, then 

press the r button. 

3. Use the u or d button to select 

Reset Menu

, then press the 

r

 button. 

4. Use the u or d button to select 

Change Toner C/M/Y/K

 

for the color of the toner cartridge you want to change, then 
press the r button. 

5. Continue with the steps in the next section to remove and 

replace the toner cartridge. 

Worn Photoconductor

The photoconductor is near the end of its 
service life. Replace the photoconductor with 
a new one.

Worn Fuser

The fuser has reached the end of its service 
life. 

Worn uuuu Dev Unit

The developer has reached the end of its 
service life. 

Replace Toner uuuu

1

The indicated toner cartridge is empty.

Replace Photocondctr

2

The photoconductor is at the end of its 
service life.