Oricom p100 Manuale Utente

 
 
 

13 of 16 

 

Key Beep 
When the key beep is turned on, you will hear a tone whenever you 
press a key on the handset.  You have the option of turning on or off the 
key beep. 
1. Press  

2   once you have entered into programming mode. 

2. Only 

the

 icon turns on.  The screen displays the current setting.  

“1” means the key beep is currently off, “2” means it is currently on.  

3. Press 

1   to turn off the key beep.  Press  2  to turn it on. 

4. Press 

 

   to confirm and return the phone to standby.   

 
 
Recall Timing Duration 
 
Recall timing default settings are; Australia 100ms and New Zealand 
600ms. You should not need to change these settings. 
 
If when you are using network services or a PBX the     button does not 
work you can select a different setting.   
1.  When the phone is in standby mode press  

   to enter 

programming mode. 

2.  Press  3      the  

 icon turns on.  

3.  The screen displays the current setting, “1” short (100ms) duration  
      or “2” long (600ms) duration. 
4.  Press  1 or   2 to  change the duration. 
5. Press 

 

   to confirm change and return to standby.  

  
 
OTHER FEATURES 
Shortcut to Turn Ringer On/Off 
You can use this shortcut to turn on/off the handset ringer when the 
phone is in standby.  Simply press and hold      the    icon turns on 
whenever the ringer is turned off.  Ensure you turn the ringer back on 
later or you will not hear incoming calls. 
 
Key Lock 
Press and hold   

   during Standby to lock or unlock the keypad.  

The    icon turns on whenever the keypad is locked. 

When the keypad is locked, pressing any key will have no effect during 
standby (except holding   

   .)  When there is an incoming call, you can 

still answer the call by pressing      .  During the call, the keypad 

 
 
 

14 of 16 

 

functions as normal.  When the call is ended, the keypad will be locked 
again.  
 
Base Ringer Volume 
Pressing and holding   

   on the base adjusts the base ringer volume.  

The ringer will be played once at the new volume level.  If the ringer is 
turned off, you will hear two short beeps. 
You cannot change the base ringer setting when you are talking on the 
phone. 

 
Finding (Paging) the Handset  
You can page or locate the handset by simply pressing   

   on the base.  

The handset produces a tone for 30 seconds and the handset display 
flashes “oooo”.  You can stop the paging by pressing any key on the 
handset. 
 
 
One Touch access to Telstra

If you have activated Telstra’s Home Messages 101 you can check if you 
have messages. This service is free to turn on from most phones in 
Australia. 
1.  Press and hold 0 for 2 seconds in standby mode. 
2. 

T

he phone will automatically go off-hook and dial the programmed 

number.  

For more information contact Telstra.

 

 
Out of Range Warning 
When you are talking on the phone and you walk too far away from the 
base, you will hear an alert tone through the earpiece.  You should walk 
back closer to the base.  Failing to do so will result in the call being 
disconnected.   

If you do not see the  icon on the display, the handset is not linked to 
the base. 
 
Returning phone to Default Settings 
If you wish to reset the handset back to its original settings it can be done 
as follows.   
1.  Once you are in programming mode, press and hold     until you 

hear the confirmation tone. 

2.  The handset settings will be reset and the phone returns to standby. 
Note: This action clears all the numbers in redial, phonebook and CID log.