Kenwood KDC-BT652U Manuale Utente
22
English
Bluetooth Setup
Selecting the Bluetooth Device
1
Press to enter Bluetooth mode.
2
Turn the volume knob to select
[SETTINGS], then press to enter.
[SETTINGS], then press to enter.
3
Turn the volume knob to select
[PAIRING], then press to enter.
[PAIRING], then press to enter.
4
Turn the volume knob to select [PHONE
SELECT] or [AUDIO SELECT], then press
to enter.
SELECT] or [AUDIO SELECT], then press
to enter.
5
Turn the volume knob to select a
Bluetooth device name.
Bluetooth device name.
6
Press the volume knob to set up the
Bluetooth device.
Bluetooth device.
■
■
“✱ (device name)”: The selected
Bluetooth device is busy.
Bluetooth device is busy.
■
■
“- (device name)”: The selected Bluetooth
device is on standby.
device is on standby.
■
■
“(blank) (device name)“: The Bluetooth
device is deselected.
device is deselected.
■
■
If two cell-phones or an audio player
have already been selected, deselect one
device before selecting a new Bluetooth
device.
have already been selected, deselect one
device before selecting a new Bluetooth
device.
7
Hold to finish the procedure.
■
■
To cancel the Bluetooth mode, press .
Bluetooth Device Registration Test
You can check whether your Bluetooth device
can be registered using this unit.
can be registered using this unit.
1
Press and hold to enter pairing mode
“PAIRING” is displayed.
“PAIRING” is displayed.
2
“PLEASE PAIR YOUR PHONE” is displayed.
■
■
When “(device name)” is displayed, select
"[PAIRING]" and press the control knob.
"[PAIRING]" and press the control knob.
■
■
When “DEVICE FULL” is displayed, delete a
Bluetooth device and retry.
Bluetooth device and retry.
1. Turn the volume knob to select the
Bluetooth device, then press and hold
to confirm.
to confirm.
2. Turn the volume knob to select “YES”,
then press to confirm.
3
Start registering this unit by operating
the Bluetooth device.
By operating the Bluetooth device, register
the hands-free unit or audio unit (pairing).
Select “KENWOOD BT CD/R-5T1” from the
list of found units.
the Bluetooth device.
By operating the Bluetooth device, register
the hands-free unit or audio unit (pairing).
Select “KENWOOD BT CD/R-5T1” from the
list of found units.
4
Input the PIN code (“0000”) in the
Bluetooth device.
Check that registration is complete on
the Bluetooth device. PIN code is set to
“0000” as the default. You can change this
code. Refer to [PIN CODE EDIT] under
<Bluetooth Setup> (page 23).
Bluetooth device.
Check that registration is complete on
the Bluetooth device. PIN code is set to
“0000” as the default. You can change this
code. Refer to [PIN CODE EDIT] under
<Bluetooth Setup> (page 23).
5
“(device name)” is displayed. Press and
hold the volume knob.
“BT TEST” is displayed.
hold the volume knob.
“BT TEST” is displayed.
6
The connection result, “OK” or “NG”, is
displayed.
displayed.
■
■
“PAIRING”: Registration to this unit
■
■
“HF CNT”: Hands-free phoning
■
■
“AUD CNT”: Audio playback
■
■
“PB DL”: Phone Book downloading
7
Press to exit pairing mode.
■
■
Data (Phone Book, etc.) of the cell-phone
checked for connection does not remain in
this unit.
checked for connection does not remain in
this unit.
Bluetooth Setup
1
Press to enter Bluetooth mode.
2
Turn the volume knob to select
[SETTINGS], then press to enter.
[SETTINGS], then press to enter.
3
Turn the volume knob to make a
selection, then press to confirm.
selection, then press to confirm.
■
■
See table below for selection.
■
■
Repeat step 3 until the desired item is
selected/activated.
selected/activated.
■
■
Press to return to the previous item.
4
Hold to finish the procedure.
■
■
To cancel the Bluetooth mode, press .
B64-4919-00_02_K.indb 22
11/12/21 9:33