Kenwood KDC-BT652U Manuale Utente

English

Press   SRC to select a source other than “STANDBY”.

Press the volume knob to enter [FUNCTION] mode.

Turn the volume knob to select [AUDIO CONTROL] or [SETTINGS], then press to enter.

Turn the volume knob to make a selection, then press to confirm.

■

■

See table below for selection.

■

■

Repeat step 4 until the desired item is selected/activated.

■

■

Press   to return to the previous item.

Hold   to finish the procedure.

[AUDIO CONTROL] : While listening to any source except in STANDBY state or Bluetooth mode.

SUB-W LEVEL

–15 — 0 * — +15: Adjusts the subwoofer output level.

BASS LEVEL

–8 — 0 * — +8: Source tone memory: Adjusts the level to memorize in each source. (Before making an 
adjustment, select the source you want to adjust.)

MID LEVEL
TRE LEVEL
EQ PRO

KDC-X696 only

BASS ADJUST

BASS CTR FRQ

60/ 80/ 100 */ 200: Selects the center frequency.

BASS LEVEL

–8 — 0 * — +8: Adjusts the level.

BASS Q FACTOR 1.00 */ 1.25/ 1.50/ 2.00: Adjusts the quality factor.
BASS EXTEND

ON: Turns on the extended bass. ; OFF *: Cancels.

MID ADJUST

MID CTR FRQ

0.5K/ 1.0K */ 1.5K/ 2.5K: Selects the center frequency.

MID LEVEL

–8 — 0 * — +8: Adjusts the level.

MID Q FACTOR 0.75/ 1.00 */ 1.25: Adjusts the quality factor.

TRE ADJUST

TRE CTR FRQ

10.0K/ 12.5K */ 15.0K/ 17.5K: Selects the center frequency.

TRE LEVEL

–8 — 0 * — +8: Adjusts the level.

PRESET EQ

NATURAL */ USER/ ROCK/ POPS/ EASY/ TOP40/ JAZZ/ POWERFUL: Selects a preset sound mode suitable 
to the music genre. (Selects [USER] to use the customized bass, middle, and treble settings.)

BASS BOOST

B.BOOST LV1/ B.BOOST LV2/ B.BOOST LV3: Selects your preferred bass boost level. ; OFF *: Cancels.

LOUDNESS

LOUDNESS LV1 */ LOUDNESS LV2: Selects your preferred low and high frequencies boost to produce a well-
balanced sound at a low volume level. ; OFF: Cancels.

BALANCE

L15 — 0 * — R15: Adjusts the left and right speaker output balance.

FADER

R15 — 0 * — F15: Adjusts the rear and front speaker output balance.

SUBWOOFER SET

ON *: Turns on the subwoofer output. ; OFF: Cancels.

DETAILED SET

HPF

THROUGH *: All signals are sent to the front speaker. ;  
100/ 120/ 150 (HZ): Frequencies lower than the specified value are cut off.

LPF 
SUBWOOFER

THROUGH *: All signals are sent to the subwoofer. ;  
85/ 120/ 160 (HZ): Frequencies higher than the specified value are cut off. 

SUB-W PHASE REVERSE (180°)/ NORMAL (0°) *: Selects the phase angle of the subwoofer output to be in line with the 

speaker output for optimum performance. (Selectable only if a setting other than [THROUGH] is selected for 
[LPF SUBWOOFER].)

B64-4919-00_02_K.indb   24

11/12/21   9:33