Honeywell International Inc. 8DL5800PIR-OD Manuale Utente
5800-OD Wireless Outdoor Motion Sensor – Installation Instructions
GENERAL INFORMATION
The Honeywell 5800-OD Wireless Outdoor Motion Sensor
(referred to as the 5800-OD) combines the convenience of wireless
technology with a full featured outdoor PIR motion sensor. The
major features are highlighted below:
(referred to as the 5800-OD) combines the convenience of wireless
technology with a full featured outdoor PIR motion sensor. The
major features are highlighted below:
Immunity to bright light
disturbances from headlights,
sunlight, and other bright
light sources.
disturbances from headlights,
sunlight, and other bright
light sources.
Very low current draw.
Discriminates both large and
small animals to reduce false
alarms.
small animals to reduce false
alarms.
Selectable detector
range and angle.
range and angle.
Battery saving circuit allows
for a 5 or 120 second period of
inactivity before being
reactivated.
for a 5 or 120 second period of
inactivity before being
reactivated.
Tamper detection.
SPECIFICATIONS
Detection Method
Passive Infrared
Initial Warm Up
~ 2 minutes
Mounting Height
0.8 - 1.2m (2.7 - 4ft) wall or pole
Range
Adjustable up to 12m (40ft)
Pattern
90° pattern consisting of 13 zones. This
pattern can be adjusted in 15° incre-
ments from center up to 45°.
ments from center up to 45°.
Sensitivity
2.0° C at 0.6m/s (3.6° F at 2.0ft/s)
Detection Speed
0.3 - 1.5m/s (1 - 5ft/s)
Operating Voltage
6 VDC (uses 4 lithium 1.5VDC AA cells)
Current
3mA max (during walk test) 10uA
(standby)
(standby)
Battery Saving Timer
Adjustable 120sec or 5sec
Alarm Period
~ 2.5 seconds
LED Indicator
Enabled during a walk test.
Disabled for normal operation.
Disabled for normal operation.
Weatherproof
IP54 compliance
Operating Temperature
– 20 to + 50 ° C (– 4 to +122° F)
Humidity
95% Max
Accessories (included)
Pole mounting kit, screw kit, detection
masking strips.
masking strips.
INSTALLATION (refer to the Component Identification Diagram on page 5)
1
Select the Mounting Position
Avoid strong sunlight into the sensor's field.
Avoid moving or swaying trees and bushes.
Orient the detector
so that intrusion
passes across the
detection field, not
into the sensor.
so that intrusion
passes across the
detection field, not
into the sensor.
Allow 110mm (4.4")
above the sensor to
enable opening the
cover.
above the sensor to
enable opening the
cover.
Choose an installation
height of 0.8m to 1.2m
(2.7 to 4ft).
height of 0.8m to 1.2m
(2.7 to 4ft).
Ensure the sensor can be
mounted on a perpendicular
wall or pole that would make
its detection pattern parallel
to the ground.
mounted on a perpendicular
wall or pole that would make
its detection pattern parallel
to the ground.
Parallel
2
Prepare the Sensor for Mounting
1.
Loosen the Captive Lock
Screw and remove the
Cover.
Screw and remove the
Cover.
2.
Remove the four (4) screws fastening the Detector
to the Back Box.
to the Back Box.
3.
Remove Detector from the Back Box.
3
Install / Replace the Battery
IMPORTANT:
Use only lithium batteries.
Use four (4) lithium 1.5VDC AA cells. (Energizer L91 or
equivalent.)
equivalent.)
Observe polarity.
Mark the date of replacement on the batteries.
1.
If necessary, loosen the
Captive Lock Screw and lift
Cover off. Then, remove 4
screws that secure the
Detector to the Back Box.
Captive Lock Screw and lift
Cover off. Then, remove 4
screws that secure the
Detector to the Back Box.
2.
Observe the proper polarity
and replace the batteries.
Ensure positive side of
battery is pointing away from
the springs.
and replace the batteries.
Ensure positive side of
battery is pointing away from
the springs.
3.
For reference, mark the date of
replacement on the batteries.
replacement on the batteries.
PLEASE GO TO PAGE 6 FOR FCC / IC STATEMENTS