Honeywell International Inc. 8DLFA270RF Manuale Utente
- 4 -
Defaulting the FA270RF
To restore the FA270RF to the default values, perform the following steps:
Step Action
1
Enter the Program mode by pressing the [1] and [3] keys simultaneously for a few seconds within 30
seconds after applying power. The keypad alternately flashes “00” and two dashes.
seconds after applying power. The keypad alternately flashes “00” and two dashes.
2
Press the [9] key. The display flashes “EE.”
3
Press the [1] key to restore the default values, or press any other key to exit without restoring the
default values.
default values.
If you pressed [1], the keypad beeps 3 times and returns to alternately flashing “00” and two dashes.
If you pressed any other key, the keypad does not beep, and returns to alternately flashing “00” and
two dashes.
If you pressed any other key, the keypad does not beep, and returns to alternately flashing “00” and
two dashes.
4 Press
[
✱] to exit the FA270RF Program Mode.
Programming Procedure
This section is divided into two parts.
• Programming for an installation WITHOUT local wireless keys.
• Programming for an installation WITH local wireless keys.
• Programming for an installation WITH local wireless keys.
Using this programming procedure is necessary only if you plan to use wireless keys beyond the control
panel’s capacity, or on a system that does not support 5800 Series wireless. Refer to the FA270RF
Application Guide on page 2 for installations that require these settings.
panel’s capacity, or on a system that does not support 5800 Series wireless. Refer to the FA270RF
Application Guide on page 2 for installations that require these settings.
Note:
See the control panel's installation instructions for the acceptable keypad and receiver addresses.
• If you are using a wireless key in High-Security mode (5804E) in the control panel, it will occupy one
of the devices in the FA270RF.
• When operating the system in High-Security mode, non-encrypted wireless keys will still function. If
you want only the encrypted keys to operate, be sure to delete all non-encrypted keys from the
system.
system.
Programming for an Installation WITHOUT Local Wireless Keys
To program the FA270RF for an installation without any local wireless keys, perform the following steps:
Step Action
Display
1
Enter the Program mode by pressing the [1] and [3] keys
simultaneously for a few seconds within 30 seconds after applying
power or within 30 seconds after removing the case back.
simultaneously for a few seconds within 30 seconds after applying
power or within 30 seconds after removing the case back.
Alternately flashes "oo" and
two dashes.
two dashes.
2
Enter [1] (Keypad Address). Enter the 2-digit keypad address (01-
31). Press the [
31). Press the [
✱] key to continue.
Alternately flashes "cA" and
the 2-digit keypad address.
the 2-digit keypad address.
3
Enter [2] (Receiver Address). Enter the 2-digit receiver address (00-
30). Press the [
30). Press the [
✱] key to continue.
Alternately flashes “rA” and
the 2-digit receiver address.
the 2-digit receiver address.
4
Enter [4] (House ID Source). Enter [1] (System) to use the House ID
programmed into the control panel, if RF keypad(s) and/or bi-
directional device(s):
programmed into the control panel, if RF keypad(s) and/or bi-
directional device(s):
• Are used on the control panel.
OR
• Neither is used.
Enter [0] (Local) to use the House ID programmed into the
FA270RF (Program Address 3).
Note: If the House ID Source is:
FA270RF (Program Address 3).
Note: If the House ID Source is:
• System (1), RF keypad and bi-directional units MUST
match the House ID programmed into the control panel.
• Local (0), RF keypad and bi-directional units MUST
match the House ID programmed into the FA270RF.
Press the [
✱] key to continue.
Alternately flashes “hl” and
either "1" or "0."
either "1" or "0."