Honeywell International Inc. 8DLFA270RF Manuale Utente
- 5 -
Step Action
Display
5
Enter [6] (Receiver Enable). Enter [1] to enable, or [0] to disable.
Enable the receiver if RF transmitters or wireless keypads are
programmed into the control.
Note: Make sure the number of receivers set for Enable (1) does not
Enable the receiver if RF transmitters or wireless keypads are
programmed into the control.
Note: Make sure the number of receivers set for Enable (1) does not
exceed the capacity of the control panel.
Press the [
✱] key to continue.
Alternately flashes “r-” and
either "1" or "0."
either "1" or "0."
6
Enter [7] (Transmitter Module Enable). Enter [1] to enable, or [0] to
disable. Enter [1] if bi-directional devices are being used.
Note: If the House ID Source is System and more than one FA270RF
disable. Enter [1] if bi-directional devices are being used.
Note: If the House ID Source is System and more than one FA270RF
is used, make sure only one has the Transmitter Module
enabled. See Note under House ID Source step 4.
enabled. See Note under House ID Source step 4.
Press the [
✱] key.
Alternately flashes “tE” and
either "1" or "0."
either "1" or "0."
7
Enter [0] (High-Security Mode). To put the system into High-
Security mode, enter [1]. Enter [0] to disable.
Security mode, enter [1]. Enter [0] to disable.
En
8
Press the [
✱] key to exit the FA270RF Program mode.
“READY” or “NOT READY”
Note: This is all the FA270RF programming necessary for this application. Upon exiting the Program mode,
the FA270RF alternately flashes "Ad," the 2-digit keypad address, and the 2-digit receiver address. If
either of these is incorrect, repeat steps 1 through 3.
either of these is incorrect, repeat steps 1 through 3.
Programming for an Installation WITH Local Wireless Keys
• The FA270RF is supplied with default settings for the functions of the wireless keys. See page 3.
•
If, during the programming of the wireless keys, you make a wrong entry and want to reprogram a
wireless key, simply press the [
wireless key, simply press the [
✱] key until “d-“ is displayed. Then enter the correct information.
Perform steps 1-6 in the Programming for an Installation Without Local Wireless Keys section. Then perform
the following steps:
the following steps:
Step Action
Display
1
Enter [3] (House ID). Enter the 2-digit House ID for the FA270RF
(01-31).
Note: The House ID is needed only if RF keypads and/or bi-
(01-31).
Note: The House ID is needed only if RF keypads and/or bi-
directional units are used and House ID source is set for Local.
The House ID entered here MUST match the House ID
programmed in the RF keypad and the bi-directional unit.
The House ID entered here MUST match the House ID
programmed in the RF keypad and the bi-directional unit.
Press the [
✱] key to continue.
Alternately flashes “hl” and
a 2-digit number.
a 2-digit number.
2
Enter [8] (Wireless Key Auto Enroll). The FA270RF automatically
advances to first available device number.
Note: If all 8 devices have been enrolled, the FA270RF beeps three
advances to first available device number.
Note: If all 8 devices have been enrolled, the FA270RF beeps three
times and continues to alternately flash "oo" and "--."
Alternately flashes "d" with
the device number; and “--.”
the device number; and “--.”
3
Press any button on the wireless key to enroll the serial number.
Note: If enrolling a wireless key (5804E) in High-Security mode, press
Note: If enrolling a wireless key (5804E) in High-Security mode, press
all four buttons on the wireless key simultaneously.
Alternately flashes "d" with
the device number; and the
serial number.
the device number; and the
serial number.
4
Press the [
✱] key to accept the serial number; OR press the [#] key to
reject the serial number.
If you accept the serial number, the FA270RF beeps twice. If you
reject the serial number, the FA270RF returns to the “enroll serial
number” prompt.
Note: A maximum of 8 wireless keys may be enrolled into the
If you accept the serial number, the FA270RF beeps twice. If you
reject the serial number, the FA270RF returns to the “enroll serial
number” prompt.
Note: A maximum of 8 wireless keys may be enrolled into the
FA270RF. These wireless keys DO NOT occupy any zones
supported by the control.
supported by the control.
If you are finished programming for now, press [
✱] to exit. Otherwise,
continue with step 5.
If you accept the serial
number, the display flashes
the device number and a
hyphen.
number, the display flashes
the device number and a
hyphen.
If you reject the serial
number, the display
alternately flashes "d" with
the device number; and “--.”
number, the display
alternately flashes "d" with
the device number; and “--.”
5
Enter [2] (User Code). Enter the 4-digit user code for the wireless
key.
Note: The user code must be a valid code that is programmed in the
key.
Note: The user code must be a valid code that is programmed in the
control panel.
Press the [
✱] key to accept the user code.
If you are finished programming for now, press [
✱] to exit. Otherwise,
continue with step 6.
Flashes "u4." Once the 4-
digit user code is entered,
the display flashes "u4," the
first two digits, and then the
last two digits of the user
code.
digit user code is entered,
the display flashes "u4," the
first two digits, and then the
last two digits of the user
code.