Honeywell International Inc. 8DLFA270RF Manuale Utente
- 7 -
Deleting, Replacing, or Editing Wireless Keys
Use the following procedure to delete, replace, or change any of the programming for a wireless key.
Step Action
Display
1
Enter the program mode by pressing the [1] and [3] keys
simultaneously for a few seconds within 30 seconds after applying
power.
simultaneously for a few seconds within 30 seconds after applying
power.
Alternately flashes "oo" and
two dashes.
two dashes.
2
Enter [5] (Wireless Key Editing). Enter the device number for the
wireless key you want to edit. This must be a device that has its
serial number programmed in the FA270RF already.
To delete the serial number, press [
wireless key you want to edit. This must be a device that has its
serial number programmed in the FA270RF already.
To delete the serial number, press [
✱], then press [9], then press [✱]
again.
To exit without deleting the serial number, press the [#] key
Press the [
To exit without deleting the serial number, press the [#] key
Press the [
✱] key to continue.
Flashes the device number
and a hyphen.
and a hyphen.
Once the device number is
entered, alternately flashes
"d" with the device number
and the serial number.
entered, alternately flashes
"d" with the device number
and the serial number.
3
To change any of the programming for the wireless key, perform one
of the following step in the Programming for an Installation WITH
Local Wireless Keys section.
• For the user code, perform step 5.
• For the loop functions, perform steps 6 and 7.
• For the on-board relay assignment, perform steps 8 to 9.
of the following step in the Programming for an Installation WITH
Local Wireless Keys section.
• For the user code, perform step 5.
• For the loop functions, perform steps 6 and 7.
• For the on-board relay assignment, perform steps 8 to 9.
Alternately flashes "d" with
the device number; and “--.”
the device number; and “--.”
4
When you have completed editing the wireless keys, press the [
✱]
key twice to exit the Program mode.
Note:
Upon exiting the Program mode, the FA270RF alternately flashes "Ad," the 2-digit keypad address, and
the 2-digit receiver address. If either of these is incorrect, repeat steps 1 through 3 in the
Programming for an Installation Without Local Wireless Keys section.
the 2-digit receiver address. If either of these is incorrect, repeat steps 1 through 3 in the
Programming for an Installation Without Local Wireless Keys section.
Troubleshooting
The following error messages cause the FA270RF to produce rapid beeps for 5 seconds. The table below
describes the error messages and the corrective actions.
describes the error messages and the corrective actions.
Display
Probable Cause
Corrective Action
Lb
Low battery in the wireless
key
key
1. Replace the battery if the wireless key has a replaceable
battery.
2. Replace the transmitter if the wireless key does not have a
replaceable battery.
OC
Open circuit
Verify that the Data Out (DO) wire is connected properly.
1C
Incompatible connection
Verify that the control panel is a First Alert control panel.
Check 09 1. FA270RF Receiver is
not communicating
2. Another device on the
keypad terminals is not
communicating to the
control panel
communicating to the
control panel
1. Verify that the Data In (DI) wire is connected properly.
2. Verify the wiring connections between the control and all other
2. Verify the wiring connections between the control and all other
devices.
Specifications
Physical:
6-5/8"W x 4-7/8"H x 1-1/8"D
(168.3mm x 123.9mm x 28.6mm)
(168.3mm x 123.9mm x 28.6mm)
Wiring:
Refer to Wiring Table on page 2
Range:
200' nominal
Frequency: 345 MHz
Voltage:
12VDC
Current:
Standby ..........................40mA
Backlighting on and
Sounder on......................100mA
Relay:
Normally Open, 1A, 28VDC
Sounder:
Piezo-electric (fire alarm is loud pulsing
tone; burglary/audible panic alarm is
continuous tone)
tone; burglary/audible panic alarm is
continuous tone)