Honeywell International Inc. 8DLLYNXREN-5 Manuale Utente
–23–
Data Field Descriptions
SYSTEM STATUS REPORT CODES (
✻
✻
✻
✻60–✻
✻
✻
✻69)
✻
60
Trouble Report Code
(See notes above)
(See notes above)
This will be sent if a zone goes into trouble.
✻
61
Bypass Report Code
(See notes above)
(See notes above)
This will be sent when a zone is manually bypassed.
✻
62
AC Loss Report Code
(See notes above)
(See notes above)
Timing of this report is random with up to a 4-hour delay. If AC restores
before the report goes out, there is no AC restore report.
before the report goes out, there is no AC restore report.
✻
63
Low Battery Report Code
(See notes above)
(See notes above)
This will be sent when a low battery condition exists in the system’s
standby battery.
standby battery.
✻
64
Test Report Code
(See notes above)
(See notes above)
This is sent periodically to test that the communicator and phone lines are
operational (frequency of report is selected in field
operational (frequency of report is selected in field
✻
51).
Note: The control validates the data entered in this field. If the selection
is not valid the control will emit a single long beep indicating that
the selection has been rejected. The control replaces the selection
with the default value which is displayed on the keypad.
the selection has been rejected. The control replaces the selection
with the default value which is displayed on the keypad.
✻
65
Open Report Code
(See notes above)
(See notes above)
This is sent upon disarming of the system. 2nd digit = user number, if
expanded or 4+2 reporting is selected.
expanded or 4+2 reporting is selected.
✻
66
Arm AWAY/STAY Report Code
(See notes above)
(See notes above)
This option allows for independent programming of AWAY and STAY
reports. 2nd digit of report is user number if expanded or 4+2 reporting is
selected.
Note: OPEN reports are not sent if the associated closing report is not
reports. 2nd digit of report is user number if expanded or 4+2 reporting is
selected.
Note: OPEN reports are not sent if the associated closing report is not
enabled.
✻
67
RF transmitter Low Batt. Report Code
(See notes above)
(See notes above)
This is sent in the event that a wireless transmitter low battery condition
exists.
exists.
✻
68
Cancel Report Code
(Always enabled, a report code can be entered if
reporting formats other than Contact ID
reporting formats other than Contact ID
®
are used)
This is sent upon disarming of the system after an alarm condition was
reported.
Note: The control validates the data entered in this field. If the
reported.
Note: The control validates the data entered in this field. If the
selection is not valid the control will emit a single long beep
indicating that the selection has been rejected. The control
replaces the selection with the default value which is displayed on
the keypad.
indicating that the selection has been rejected. The control
replaces the selection with the default value which is displayed on
the keypad.
✻
69
Recent Closing Report
(This feature is always enabled. A report code can be
entered if formats other than Contact ID
entered if formats other than Contact ID
®
are used)
Sent when an alarm occurs within two minutes after exit delay expires.
Disarming the system within the two minutes stops the alarm sound and
the keypad displays the faulted zone number (and will display “CA” if
cancel display option in field *57 is enabled.) No messages are sent to the
Central Station.
If the system is not disarmed within two minutes, the alarm sound
continues and a “Recent Closing” and a “Zone Alarm” message are sent to
the Central Station (after dial delay expires).
Note: The control validates the data entered in this field. If the selection
Disarming the system within the two minutes stops the alarm sound and
the keypad displays the faulted zone number (and will display “CA” if
cancel display option in field *57 is enabled.) No messages are sent to the
Central Station.
If the system is not disarmed within two minutes, the alarm sound
continues and a “Recent Closing” and a “Zone Alarm” message are sent to
the Central Station (after dial delay expires).
Note: The control validates the data entered in this field. If the selection
is not valid the control will emit a single long beep indicating that
the selection has been rejected. The control replaces the selection
with the default value which is displayed on the keypad.
the selection has been rejected. The control replaces the selection
with the default value which is displayed on the keypad.
RESTORE REPORT CODES (
✻
70–
✻
76)
✻
70
Alarm Restore Report Code, 1st Digit
(See notes above)
(See notes above)
Sent when the zone that caused an alarm is restored to its non-faulted
condition. 2nd digit is automatically sent as the 2nd digit of the zone
alarm report code programmed in field
condition. 2nd digit is automatically sent as the 2nd digit of the zone
alarm report code programmed in field
✻
56, if expanded or 4+2 reporting
is selected.
✻
71
Trouble Restore Report Code
(See notes above)
(See notes above)
Sent when a trouble in a zone is restored.
✻
72
Bypass Restore Report Code
(See notes above)
(See notes above)
Sent when a zone that has been bypassed is unbypassed.
✻
73
AC Restore Report Code
(See notes above)
(See notes above)
Sent when AC power has been restored after an AC power outage.
✻
74
Low Battery Restore Report Code
(See notes above)
(See notes above)
Sent when a system low battery condition is restored to normal.