HP A2Y15AV Manuale Utente
Processor Configuration Registers
36
Datasheet, Volume 2
2.3.7
Graphics Memory Address Ranges
The integrated memory controller can be programmed to direct memory accesses to
IGD when addresses are within any of two ranges specified using registers in MCH
Device 2 configuration space.
IGD when addresses are within any of two ranges specified using registers in MCH
Device 2 configuration space.
1. The Graphics Memory Aperture Base Register (GMADR) is used to access graphics
memory allocated using the graphics translation table.
2. The Graphics Translation Table Base Register (GTTADR) is used to access the
translation table and graphics control registers. This is part of GTTMMADR register.
These ranges can reside above the Top-of-Low-DRAM and below High BIOS and APIC
address ranges. They MUST reside above the top of memory (TOLUD) and below 4 GB
so they do not steal any physical DRAM memory space.
address ranges. They MUST reside above the top of memory (TOLUD) and below 4 GB
so they do not steal any physical DRAM memory space.
Alternatively, these ranges can reside above 4 GB, similar to other BARs which are
larger than 32 bits in size.
larger than 32 bits in size.
GMADR is a Prefetchable range in order to apply USWC attribute (from the processor
point of view) to that range. The USWC attribute is used by the processor for write
combining.
point of view) to that range. The USWC attribute is used by the processor for write
combining.
2.3.7.1
IOBAR Mapped Access to Device 2 MMIO Space
Device 2, integrated graphics device, contains an IOBAR register. If Device 2 is
enabled, then IGD registers or the GTT table can be accessed using this IOBAR. The
IOBAR is composed of an index register and a data register.
enabled, then IGD registers or the GTT table can be accessed using this IOBAR. The
IOBAR is composed of an index register and a data register.
MMIO_Index: MMIO_INDEX is a 32 bit register. A 32-bit (all bytes enabled) I/O write
to this port loads the offset of the MMIO register or offset into the GTT that needs to be
accessed. An I/O Read returns the current value of this register. I/O read/write
accesses less than 32 bits in size (all bytes enabled) will not target this register.
to this port loads the offset of the MMIO register or offset into the GTT that needs to be
accessed. An I/O Read returns the current value of this register. I/O read/write
accesses less than 32 bits in size (all bytes enabled) will not target this register.
MMIO_Data: MMIO_DATA is a 32 bit register. A 32 bit (all bytes enabled) I/O write to
this port is re-directed to the MMIO register pointed to by the MMIO-index register. An
I/O read to this port is re-directed to the MMIO register pointed to by the MMIO-index
register. I/O read/write accesses less than 32 bits in size (all bytes enabled) will not
target this register.
this port is re-directed to the MMIO register pointed to by the MMIO-index register. An
I/O read to this port is re-directed to the MMIO register pointed to by the MMIO-index
register. I/O read/write accesses less than 32 bits in size (all bytes enabled) will not
target this register.
The result of accesses through IOBAR can be:
• Accesses directed to the GTT table (that is, route to DRAM).
• Accesses to internal graphics registers with the device.
• Accesses to internal graphics display registers now located within the PCH (that is,
• Accesses to internal graphics registers with the device.
• Accesses to internal graphics display registers now located within the PCH (that is,
route to DMI).
Note:
GTT table space writes (GTTADR) are supported through this mapping mechanism.
This mechanism to access internal graphics MMIO registers must not be used to access
VGA I/O registers that are mapped through the MMIO space. VGA registers must be
accessed directly through the dedicated VGA I/O ports.
VGA I/O registers that are mapped through the MMIO space. VGA registers must be
accessed directly through the dedicated VGA I/O ports.
2.3.7.2
Trusted Graphics Ranges
No trusted graphics ranges are supported.