Beha Amprobe GT-800 STD KITVDE-tester 4472062 Manuale Utente
Codici prodotto
4472062
GT-600/GT-800 Instruction Manual
66
-
Fuse F2
Pre-test.
If the F2 fuse is blown, then “FUSE 2!” message will be
displayed and further P/I
If the F2 fuse is blown, then “FUSE 2!” message will be
displayed and further P/I
L
tests will be disabled.
CLAMP -
Internal fuse
If internal fuse is blown, then “ERROR 2!” message will
be displayed and further CLAMP tests will be disabled.
be displayed and further CLAMP tests will be disabled.
CORD
-
U
L IEC
50 V
-
U
N IEC
50 V
Pre-test.
If an external voltage higher than 50 V is detected after
pressing START key, then “EXTERNAL VOLTAGE!”
message will be displayed and further CORD tests will be
disabled.
If an external voltage higher than 50 V is detected after
pressing START key, then “EXTERNAL VOLTAGE!”
message will be displayed and further CORD tests will be
disabled.
-
U
EXT PROBE1/GND
50 V
-
U
EXT PROBE2/GND
50 V
Pre-test and during the R
PE
test.
If an external voltage higher than 50 V is detected, then
“EXTERNAL VOLTAGE!” message will be displayed and
further CORD tests will be disabled.
“EXTERNAL VOLTAGE!” message will be displayed and
further CORD tests will be disabled.
-
Fuse F3
Pre-test.
If the F3 fuse is blown, then “FUSE 3!” message will be
displayed and further CORD tests will be disabled.
If the F3 fuse is blown, then “FUSE 3!” message will be
displayed and further CORD tests will be disabled.
PRCD
-
U
L IEC
50 V
-
U
N IEC
50 V
Pre-test and during the R
PE
test.
If an external voltage higher than 50 V is detected, then
“EXTERNAL VOLTAGE!” message will be displayed and
further PRCD tests will be disabled.
“EXTERNAL VOLTAGE!” message will be displayed and
further PRCD tests will be disabled.
-
I
SUB INT
0.15 mA
Path pre-test (self-test).
If the instrument’s measurement path is interrupted e.g.
due to blown internal fuse, then “ERROR 1” message
will be displayed and further P/I
If the instrument’s measurement path is interrupted e.g.
due to blown internal fuse, then “ERROR 1” message
will be displayed and further P/I
L
tests will be disabled.
-
Grounding of mains
plug PE terminal
Pre-test.
If the PE terminal is not sufficiently grounded, then “PE
DISCONNECTED! TURN OFF NOW!” message will be
displayed and any further operation will be disabled.
Switch off the tester immediately, danger!
If the PE terminal is not sufficiently grounded, then “PE
DISCONNECTED! TURN OFF NOW!” message will be
displayed and any further operation will be disabled.
Switch off the tester immediately, danger!
-
Fuse F2
Pre-test.
If the F2 fuse is blown, then “FUSE 2!” message will be
displayed and further PRCD tests will be disabled.
If the F2 fuse is blown, then “FUSE 2!” message will be
displayed and further PRCD tests will be disabled.
-
I
SUB
3.50 mA
Pre-test.
If the substitute leakage current exceeds 3.50 mA
(damaged appliance), then “LN-PE SHORTED!” message
will be displayed and further PRCD tests will be disabled.
If the substitute leakage current exceeds 3.50 mA
(damaged appliance), then “LN-PE SHORTED!” message
will be displayed and further PRCD tests will be disabled.
-
I
SUB
20.00 mA
Pre-test.
If the substitute leakage current exceeds 20.00 mA
(damaged appliance), then “LN-PE SHORTED!” message
will be displayed and further CORD
If the substitute leakage current exceeds 20.00 mA
(damaged appliance), then “LN-PE SHORTED!” message
will be displayed and further CORD
tests will be disabled.
-
Fuse F3
Pre-test in R
PE
measurement.
-
U
EXT PROBE1/GND
50 V Pre-test and during the measurement in R
PE
measurement
-
U
EXT PROBE2/GND
50 V Pre-test and during the measurement in R
PE
measurement