Yaesu FT-450D Manuale Utente
Page 86
FT-450D O
PERATION
M
ANUAL
STBY BP (STBY BEEP)
Function: Setting of standby beep
Available Values: OFF / ON
Default: OFF
OFF:
Available Values: OFF / ON
Default: OFF
OFF:
No beep sound is transmitted.
ON:
A beep is transmitted before returning to
receive.
receive.
The beep, transmitted when the PTT is released, will
inform the other operators that your transmission has
ended.
inform the other operators that your transmission has
ended.
TONE F (TONE FREQ)
Function: Sets the CTCSS Tone Frequency.
Available Values: 67.0 ~ 254.1 (Hz)
Available Values: 67.0 ~ 254.1 (Hz)
50 Standard CTCSS tones
Default: 88.5 (Hz)
TOT (TOT TIME)
Function: Selects the time of the Time-Out-Timer.
Available Values: OFF/1 ~ 20 (min)
Default: OFF
Available Values: OFF/1 ~ 20 (min)
Default: OFF
M
ENU
M
ODE
TUNER (TUNER/ATAS)
Function: Setting of the Auto Antenna and Antenna
Tuner
Available Values: ATAS / EXT ATU / INT ATU
/ INTRATU / F RANS
Default: INT ATU
Selects the device (FC-40 or ATAS-100/-120/-120A)
controlled by the front panel’s [TUNE] button.
ATAS:
/ INTRATU / F RANS
Default: INT ATU
Selects the device (FC-40 or ATAS-100/-120/-120A)
controlled by the front panel’s [TUNE] button.
ATAS:
The [TUNE] button will activate the op-
tional ATAS-100/-120/-120A on the HF
amateur bands and 50 MHz amateur
band.
tional ATAS-100/-120/-120A on the HF
amateur bands and 50 MHz amateur
band.
EXT ATU: The [TUNE] button will activate the op-
tional FC-40.
INT ATU: The [TUNE] button will activate the An-
tenna Tuner. The tuner passes only the
Transmitter RF.
Transmitter RF.
INTRATU: The [TUNE] button will activate the An-
tenna Tuner. The tuner passes both the
Transmitter RF and the Receiver signal.
Transmitter RF and the Receiver signal.
F TRANS: The frequency data of the radio is sent to
another FT-450D. This feature is very
usefll for the “SO2R” (Single Operator,
Two Radio) operation. In this case, the in-
terconnection is as follows.
usefll for the “SO2R” (Single Operator,
Two Radio) operation. In this case, the in-
terconnection is as follows.
INPUT
DC 13.8V
22A
ANT
GND
EXT
SPKR
CAT
LINEAR
TUNER
DATA
INPUT
DC 13.8V
22A
ANT
GND
EXT
SPKR
CAT
LINEAR
TUNER
DATA
TU
N
E
R
C
AT
Junction Connector
Dsub 9pin to Dsub 9pin
Cross Cable
CT-62
M
ASTER
S
ETTING
Set menu itme “TUNER” to “F TRANS”.
S
LAVE
T
RANSCEIVER
S
ETTING
Set menu itme “CAT RTS” to “DISABLE”.
Set menu itme “CATRATE” to “4800 bps”.
Set menu itme “CATRATE” to “4800 bps”.
O
PERATION
When the [TUNE] button on the Master Transceiver is pressed, the
Slave Transceiver frequency becomes the same as the Master Trans-
ceiver.
Slave Transceiver frequency becomes the same as the Master Trans-
ceiver.
I
MPORTANT
N
OTICE
Please install an antenna protection circuit so the Master (RX) Trans-
ceiver is not damaged when the Slave (TX) Transceiver is transmitting.
ceiver is not damaged when the Slave (TX) Transceiver is transmitting.