Futaba 10CAG Manuale Istruttivo
34
MODEL TYPE
: sets the type of programming used for this model.
The T10CG has 15 model memories, which can each support:
•one powered aircraft (ACRO
•one powered aircraft (ACRO
PHPRU\ W\SH ZLWK PXOWLSOH ZLQJ DQG WDLO FRQ¿JXUDWLRQV 6HH WZLQ DLOHURQ VHUYRV WZLQ
elevator servos, ELEVON, and V-TAIL for further information.);
WKUHHJOLGHUZLQJW\SHV DJDLQZLWKPXOWLSOHWDLOFRQ¿JXUDWLRQV 6HH*OLGHUMODEL TYPE for details, p. 78;
•eight helicopter swashplate types, including CCPM. See Helicopter MODEL TYPE for details, p. 93.
WKUHHJOLGHUZLQJW\SHV DJDLQZLWKPXOWLSOHWDLOFRQ¿JXUDWLRQV 6HH*OLGHUMODEL TYPE for details, p. 78;
•eight helicopter swashplate types, including CCPM. See Helicopter MODEL TYPE for details, p. 93.
%HIRUHGRLQJDQ\WKLQJHOVHWRVHWXS\RXUDLUFUDIW¿UVW\RXPXVWGHFLGHZKLFKMODEL TYPEEHVW¿WVWKLVSDUWLFXODUDLUFUDIW
(Each model memory may be set to a different model type.) If your transmitter is a T10CAG, the default is ACRO. If it is a
T10CHG, the default is HELI(H1).
(Each model memory may be set to a different model type.) If your transmitter is a T10CAG, the default is ACRO. If it is a
T10CHG, the default is HELI(H1).
ACRO
is the best choice for most powered airplanes, but in some circumstances, GLID(2A+1F) may be a better choice. ACRO
is usually a better choice because of functions it offers that the GLID types do not:
•ACRO adds:
•SNAP-ROLL
•AILEVATOR (twin elevator servo support)
•For fuel-powered airplanes: IDLE-DOWN, THR-CUT, THROTTLE-NEEDLE mixing and THROTTLE DELAY programming.
•AILEVATOR (twin elevator servo support)
•For fuel-powered airplanes: IDLE-DOWN, THR-CUT, THROTTLE-NEEDLE mixing and THROTTLE DELAY programming.
•But ACRO lacks:
•5 seperate conditions for optional setups (START
SPEEDDISTANCELANDING)
If you are using a glider or heli MODEL TYPE, please go to that chapter now to select the proper model type and support
your model setup. Note that changing MODEL TYPE resets all data for the model memory, including its name.
your model setup. Note that changing MODEL TYPE resets all data for the model memory, including its name.
GOAL of EXAMPLE:
STEPS:
INPUTS:
Select the proper MODEL TYPE for your
model. Ex: ACRO.
model. Ex: ACRO.
[NOTE: This is one of several functions
that requires confirmation to make a
change. Only critical changes require
additional keystrokes to accept the
change.]
that requires confirmation to make a
change. Only critical changes require
additional keystrokes to accept the
change.]
Open the BASIC menu, then open the
PARAMETER
PARAMETER
submenu.
Turn on the transmitter.
for 1 second.
(If ADVANCE,
again.)
then
C
to highlight PARAMETER.
to choose PARAMETER.
Go to MODEL TYPE.
C
to TYPE.
Select proper MODEL TYPE.
Ex: ACRO.
&RQ¿UPWKHFKDQJH
Close PARAMETER.
Ex: ACRO.
&RQ¿UPWKHFKDQJH
Close PARAMETER.
to ACROBATIC.
for 1 second.
Are you sure?
displays.
WRFRQ¿UP
to return to BASIC menu.