Futaba 10CAG Manuale Istruttivo
35
Modulation select (MODUL): sets the type of modulation transmitted.
The modulation of your receiver will determine whether you utilize 2.4G-10CH or 2.4G-7CH setting in MODUL during
transmission. Note that you have to turn your transmitter off and back on before a modulation change becomes effective.
Be sure you understand and set the FailSafe (F/S ) settings as you intended (see p. 50).
The modulation of your receiver will determine whether you utilize 2.4G-10CH or 2.4G-7CH setting in MODUL during
transmission. Note that you have to turn your transmitter off and back on before a modulation change becomes effective.
Be sure you understand and set the FailSafe (F/S ) settings as you intended (see p. 50).
2.4G-10CH
7CH = FASST-2.4GHz system (10CHPRGH7CH mode)
Adjustability:
• 2.4G-10CH setting for all Futaba FASST-2.4G Multi-ch mode receivers,
• 2.4G-10CH setting for all Futaba FASST-2.4G Multi-ch mode receivers,
UHJDUGOHVVRIQXPEHURIFKDQQHOVLH5+65+65)65)6
• 2.4G-7CH setting for all Futaba FASST-2.4G 7ch mode receivers, regardless of
QXPEHURIFKDQQHOVLH5))5))05)65)6
NOTE: When you change models in MODEL SELECT, if the new model is set to the other modulation type,
\RXPXVWF\FOHWKHWUDQVPLWWHUSRZHUWRFKDQJHPRGXODWLRQV7KHPRGXODWLRQZLOOÀDVKRQWKHKRPHVFUHHQ
to remind you until you do so. See p. 30, MODEL SELECT, for details.
\RXPXVWF\FOHWKHWUDQVPLWWHUSRZHUWRFKDQJHPRGXODWLRQV7KHPRGXODWLRQZLOOÀDVKRQWKHKRPHVFUHHQ
to remind you until you do so. See p. 30, MODEL SELECT, for details.
GOAL of EXAMPLE:
STEPS:
INPUTS:
Change model 1 from 2.4G-10CH to
2.4G-7CH
2.4G-7CH
.
Confirm you are currently using the
proper model memory (Ex: 1)
proper model memory (Ex: 1)
On home screen, check model name and
number on top left and the modulation
on top right. If it is not the correct
model, use MODEL SELECT, p. 30.
number on top left and the modulation
on top right. If it is not the correct
model, use MODEL SELECT, p. 30.
O p e n B A S I C m e n u , t h e n o p e n
PARAMETER
PARAMETER
submenu.
for 1 second.
(If ADVANCE,
again.)
to 2nd page of menu.
C
to PARAMETER.
Go to MODUL and change setting.
C
to MODUL.
to 2.4G-7CH.
cycle power
ÀDVKHVRQVFUHHQ
Close menu and cycle power.
POWER OFF. POWER ON.
Where next?
Now that the model is in the proper modulation, the T10CG should communicate
ZLWKWKHUHFHLYHU,ILWGRHVQRWFRQ¿UPWKHW\SHRIWKHUHFHLYHU
Change MODEL TYPE
ZLWKWKHUHFHLYHU,ILWGRHVQRWFRQ¿UPWKHW\SHRIWKHUHFHLYHU
Change MODEL TYPE
WRJOLGHUKHOLFRSWHUVHHS
Set F/S settings for when 2.4G receiver sees interference: see p. 50.
Utilize servo REVERSE: see p. 38.
Adjust servo travel with END POINT: see p. 39.
6HWXSGXDOWULSOHUDWHVDQGH[SRQHQWLDOD/R,EXP): see p. 42.
Utilize servo REVERSE: see p. 38.
Adjust servo travel with END POINT: see p. 39.
6HWXSGXDOWULSOHUDWHVDQGH[SRQHQWLDOD/R,EXP): see p. 42.