Elite Video vsx33 ユーザーズマニュアル

En

Top Menu screen is not 
displayed on browser.

This receiver’s IP address has not been entered 
into the browser correctly.

Check the receiver’s IP address and enter it 
correctly in the browser (page 85).

Receiver cannot be operated 
from browser.

JavaScript is disabled on the internet browser.

Enable  JavaScript.

The browser is not compatible with JavaScript.

Use an internet browser that is compatible with
JavaScript.

Receiver’s power does not 
turn on when the power is 
turned on using the Web 
Control function.

Network Standby at Network Setup is set to 
OFF. 

Set Network Standby at Network Setup to ON 
(page 86).

The HDMI indicator blinks 
continuously.

• Check all the points below.

No picture or sound.

• This receiver is HDCP-compatible. Check that the components you are connecting are also HDCP-
compatible. If they are not, please connect them using the component or composite video jacks.
• Depending on the connected source component, it’s possible that it will not work with this receiver 
(even if it is HDCP-compatible). In this case, connect using the component or composite video jacks 
between source and receiver.
• If the problem still persists when connecting your HDMI component directly to your monitor, 
please consult the component or monitor manual or contact the manufacturer for support.
• If video images do not appear on your TV, try adjusting the resolution, DeepColor or other setting 
for your component.
• While analog video signals are being output over HDMI, use a separate connection for audio 
output.

• To output signals in DeepColor, use an HDMI cable (High Speed HDMI

 Cable) to connect this 

receiver to a component or TV with the DeepColor feature.

No picture.

• Try changing the Resolution setting (in Setting the Video options on page 61).
• VSX-33 only: Set the HDMI output setting to the connected HDMI OUT terminal (in Switching the 
HDMI output (VSX-33 only) on page 64).

No sound, or sound suddenly 
ceases.

• Check that the HDMI AV setting is set to AMP/THROUGH.
• If the component is a DVI device, use a separate connection for the audio.
• If analog video is being output over HDMI, please use a separate connection for the audio.
• Check the audio output settings of the source component.
• HDMI format digital audio transmissions require a longer time to be recognized. Due to this, 
interruption in the audio may occur when switching between audio formats or beginning playback.
• Turning on/off the device connected to this unit's HDMI OUT terminal during playback, or 
disconnecting/connecting the HDMI cable during playback, may cause noise or interrupted audio.

Noisy or distorted picture.

• Sometimes a video deck may output a noisy video signal (during scanning, for example), or the 
video quality may just be poor (with some video game units, for example). The picture quality may 
also depend on the settings, etc. of your display device. Switch off the video converter and reconnect 
the source and display device using the same type of connection (component or composite), then 
start playback again.
• If the problem still persists when connecting your HDMI component directly to your monitor, 
please consult the component or monitor manual or contact the manufacturer for support.

HDCP ERROR shows in the 
display.

• Check whether or not the connected component is compatible with HDCP. If it is not compatible 
with HDCP, reconnect the source device using a different type of connection (component or 
composite). Some components that are compatible with HDCP still cause this message to be 
displayed, but so long as there is no problem with displaying video, this is not a malfunction.

When Control with HDMI is 
set to ON, the HDMI Input 
assignment at Input Setup is 
canceled.

• Even when Control with HDMI is set to ON, for Digital In assignment of HDMI 1 is not canceled, 
so in this case use the HDMI 1 input.

VSX-33_UXJCB.book  95 ページ  ２０１０年３月９日　火曜日　午前１０時３９分