Korg Electric Keyboard ユーザーズマニュアル

☞ For details on insert effects, refer to p.155 “7. Effect 

Specifies the bus to which the program oscillator(s) of each 
track 1–8, 9–16 will be sent. You can also set the amount of 
signal that will be sent to the master effects.

Specifies the output bus for the program oscillators of tracks 
1–8 and 9–16.
The state of the settings can be viewed in the Setup page. 
(☞COMBI 7.1–1a)

Here you can adjust the send levels from tracks 1–8, 9–16 to 
master effects 1 and 2. This is valid when “BUS Select” is set 
either to L/R or Off. If IFX is selected, the send level to the 
master effects 1 and 2 is set by the (“S1 (Send1(MFX1))” and 
“S2 (Send2(MFX2))” parameters located in the Setup page, 
after the signal passes through IFX.
These settings have no effect if “BUS Select” is set to 1, 2 or 
1/2

.

The send 1 and 2 settings you make here will be used when 
the song is played or recorded from the beginning. If you 
change the settings while recording, the change will be 
recorded as part of the musical data, and the send amount 
will change when the data is played back. You can also 
change these settings during playback. However if send 1 
and 2 data has been recorded, the settings will change 
accordingly.

If “Status” (3.1–1(2)a) is either INT or BTH, CC#93 and 
#91 can be received to control send 1 and 2 respectively 
and change their settings. When you switch songs or 
return to the beginning of a song, tracks whose “Status” 
is EXT, EX2 or BTH will transmit these settings via 
MIDI. This data will be transmitted on the MIDI chan-
nel of each track as set by “MIDI Channel” (3.1–1(2)a). 
The actual send level is determined by summing the 
value of these parameters with the send level settings of 
the oscillator(s) of the program used by the track (“S1 
(Send1(MFX1))” and “S2 (Send2(MFX2))” PROG 7.1–
2a).

■

☞ “Memory Status,” “Solo Selected Track” (1.1–1d), “DKit 

IFX Patch” (COMBI 7.1–1b), “FF/REW Speed,” “Set Loca-
tion” (1.1–1d)

☞PROG 7.1–1c
However, the MIDI control channel specified in “Control 
Channel” of the 7.1: Insert FX, Setup page will not be copied.

Here you can select the type of the insert effects, turn them 
on/off etc.

These parameters are the same as in Program mode. 
(☞PROG 7.1–2)
However, this differs from Program mode in that insert 
effect dynamic modulation (Dmod) and the “Pan (CC#8),” 
“Send1(MFX1),” and “Send2(MFX2)” which follow the 
insert effect are controlled on the MIDI channel specified by 
“Control Channel” (7.1–1b). The control changes used are 
the same as in Program mode.
The pan (CC#8) and Send 1 and 2 that you specify here are 
used when playing or recording from the beginning of the 
song. If you change these settings while recording, the set-
tings will be recorded as musical data, and during playback, 
the settings will change accordingly. You can also change 
these settings during playback. However if Pan (CC#8) and 
Send 1/2 data has already been recorded, the settings will 
change according to the recorded data.

If the “Status” (3.1–1(2)a) is INT or BTH, receiving 
CC#8, #93, or #91 will cause the post- insert effect pan 
and send 1/2 to be controlled, changing the settings. 
When you change songs or return to the beginning of 
the song, tracks whose “Status” is BTH, EXT, or EX2 
will transmit these settings on the MIDI channel speci-
fied by “Control Channel.”

7.1–1a

1.1–1c

7.1–1b

7.1–3a

7.1–3c

7.1–3d

7.1–3b