Sharp MX-M182 ユーザーズマニュアル
36
COPY FUNCTIONS
3
USING THE BYPASS TRAY TO COPY A SPECIAL SIZE ORIGINAL
When the bypass tray is being used for copying and an original that is placed on the document glass is detected as
being a special size, the display will prompt the user to set the original size. To make a copy in this type of situation,
follow the steps below.
being a special size, the display will prompt the user to set the original size. To make a copy in this type of situation,
follow the steps below.
1
Load paper in the bypass tray and place
the original on the document glass.
the original on the document glass.
2
Touch the [PAPER SELECT] key and
then select the bypass tray.
then select the bypass tray.
A message will appear asking you whether you wish to
set the original size or make the copy without setting it.
To make a copy without setting the original size, press the
[START] key (
set the original size or make the copy without setting it.
To make a copy without setting the original size, press the
[START] key (
). To set the original size, go to step 3.
3
Press the [OK] key.
The original size selection screen appears with "SIZE
INPUT" selected.
INPUT" selected.
4
Select AB or inches with the [
] or
[
] key, and then select the original
size with the [
] or [
] key.
5
Press the [OK] key.
If "SIZE INPUT" was selected in step 4:
The size entry screen appears and is ready for entry of
the width of the original.
the width of the original.
If other than "SIZE INPUT" was selected in step 4:
You will return to the base screen. Go to step 8.
6
Select "X" (width) with the [
] or [
] key
and enter the width with the [
] or [
] key,
and then do the same for the length (Y).
7
Press the [OK] key.
You will return to the base
screen.
screen.
8
Press the [START] key (
).
Copying begins.
If you load thick paper in the bypass tray,
press the [PAPER] key until "EXTRA" is
highlighted. The paper type is set to thick
paper. The setting is cleared when "Auto
clear" works or the [CA] key is pressed.
For restrictions on paper types and weights,
see "PAPER"
press the [PAPER] key until "EXTRA" is
highlighted. The paper type is set to thick
paper. The setting is cleared when "Auto
clear" works or the [CA] key is pressed.
For restrictions on paper types and weights,
see "PAPER"
.
COPY RATIO
ADDRESS
ADDRESS
ADDRESS
RE
ODE
AM
AM
PAPER SELECT
RESOLUTION
RESOLUTION
RESOLUTION
RESOLUTION
AUTO IMAGE
FORMAT
BROADCAST
O
O
O
100%
AUTO
EXTRA
[OK]:ORIG. SIZE
ENTER
ENTER
Note
100%
AUTO
EXTRA
[OK]:ORIG. SIZE
ENTER
ENTER
GHI
PQRS
BACK
OK
AN
PY
A4R
A5
A5
ORIG. SIZE ENTER
AB
SIZE INPUT
PQ
ACC
LEX SCAN
LEX SCAN
LEX SCAN
ED COPY
If you selected inches in step 4, the screen will
be ready for you to enter the width in inches.
be ready for you to enter the width in inches.
• Any number from 64 mm to 432 mm (2-1/2"
to 17") can be entered for the width, and
any number from 64 mm to 297 mm (2-1/2"
to 11-5/8") can be entered for the length.
any number from 64 mm to 297 mm (2-1/2"
to 11-5/8") can be entered for the length.
• The entered size is retained until the
power is turned off, even if "SIZE INPUT"
is selected again and the entry screen of
step 5 is displayed.
is selected again and the entry screen of
step 5 is displayed.
OK
X:
Y:
Y:
210
148
148
SIZE INPUT
SIZE(mm)
Note
X:
Y:
Y:
100
100
100
(mm)
SIZE INPUT
SIZE
Note
OK
MNO
WXYZ
@.-_
AD-END