Genie 1500 ユーザーズマニュアル
©2011 The Genie Company
9/2011
6
PROGRAMMING REMOTES
to New Intellicode® 2 Openers.
to New Intellicode® 2 Openers.
All type remotes program in the same way.
Bring remote(s) to powerhead location. For Car2U® and
HomeLink®, park car outside the garage with the ignition
key in the “ACCESSORY” position. Each button must
be programmed individually following steps below.
HomeLink®, park car outside the garage with the ignition
key in the “ACCESSORY” position. Each button must
be programmed individually following steps below.
NOTE: For additional openers—repeat the steps above
using a different remote button for each.
using a different remote button for each.
The default setting of Intellicode® 2 must be changed.
The LED color displayed on the remote indicates
the IntelliCode® mode.
the IntelliCode® mode.
Red = IntelliCode® 1 / Green = IntelliCode® 2
FCC and IC CERTIFIED
This device complies with FCC Part 15 and RSS 210 of Industry Canada.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harful interference to radio or television
reception, which may be determined by turning the equipment OFF
and ON, the user is encouraged to try to correct the interference by
one or more of the following measures:
s Re-orient or relocate the receiver antenna.
s Increase the separation between the opener and receiver.
s Connect the opener into an outlet on a circuit different from that to
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harful interference to radio or television
reception, which may be determined by turning the equipment OFF
and ON, the user is encouraged to try to correct the interference by
one or more of the following measures:
s Re-orient or relocate the receiver antenna.
s Increase the separation between the opener and receiver.
s Connect the opener into an outlet on a circuit different from that to
which the receiver is connected.
s Consult your local dealer.
PROGRAM
SET
DOOR MOVES
DOOR MOVES
Press & Hold for
2 seconds or until
round LED turns blue.
2 seconds or until
round LED turns blue.
Press & Release that same
button again.
button again.
REMOTE BUTTON IS PROGRAMMED
OFF
Both LEDs Off.
OFF
OFF
BLUE
OFF
Select a button
NOT prorammed
to a new
Intellicode®2
opener
NOT prorammed
to a new
Intellicode®2
opener
Press & hold that button
for until both the
RED & GREEN LEDs are ON.
Release.
for until both the
RED & GREEN LEDs are ON.
Release.
Press the same remote
button 3 times.
button 3 times.
Press the same
remote button
twice.
remote button
twice.
Press the
Lean Code
Button
Lean Code
Button
REMOTE BUTTON IS PROGRAMMED TO OPENER
PROGRAMMING INTELLICODE® 2 REMOTES
to Intellicode® 1 (previous model) Openers.
to Intellicode® 1 (previous model) Openers.
Press the same
remote button
again.
remote button
again.
RED
WHEN BUTTON PRESSED
Find the Learn Code Button and
Learn Code Indicator LED on your
door opener.
Learn Code Indicator LED on your
door opener.
–
–If Door Opener does not have an
Antenna, you have an External
Receiver. The External Receiver
cover must be removed to
Receiver. The External Receiver
cover must be removed to
access the Learn Code Button
and Indicator LED.
and Indicator LED.
Red Indicator
LED
LED
Learn
Code
Button
Code
Button
Located
on Opener
Housing
on Opener
Housing
If your Door Opener has a black
antenna wire and the serial
number does not start with
10 or higher, the Learn Code
Button and Indicator LED are
located near the antenna. (The
light lens may need to be
opened. If you use an external
receiver, it may need to be
opened to access the Learn
Code Button and Indicator LED.
antenna wire and the serial
number does not start with
10 or higher, the Learn Code
Button and Indicator LED are
located near the antenna. (The
light lens may need to be
opened. If you use an external
receiver, it may need to be
opened to access the Learn
Code Button and Indicator LED.
Red Indicator LED BLINKS
Red Indicator LED OFF
1
2
3
4
5
6
1
ACTION
LED INDICATION/RESULT
ACTION
LED INDICATION/RESULT
Choose a button on your
remote device. Press &
release it twice.
remote device. Press &
release it twice.
2
3
(Follow the TOP 2 steps above to shift back to Intellicode®2)
STAYS ON
RED & GREEN
REMOTE BUTTON IS INTELLICODE® 1
PURPLE
FLASHING
OFF
PURPLE
STEADY