Genie 1500 ユーザーズマニュアル

8

©2011 The Genie Company

9/2011

s

 release handle 

DOWN and let go to release door carriage assembly 
from drive system.

s

s

freely and smoothly.

’

’

d let go.

n

a

 

t

e

e

f

 

4

o

t

 

3

 

about

 

y

l

l

a

u

n

a

m

 

r

o

o

d

 

e

s

i

a

– Door should remain stationary or move very slowly.
– If door moves quickly, CONTACT A TRAINED 

DOOR SYSTEM TECHNICIAN.

s

position (pull release handle toward opener and let go).

– Operate door using a remote or wall console. 
– Door will re-attach itself to carriage assembly.

Check that both the RED and GREEN LEDs are ON steady.
This indicates the system is working properly. If both LEDs 
are not ON steady, check the appropriate items below.

If the system appears to be working properly, perform the 
check as follows:
  1.  Start the door closing.
  2.  Pass on object through the beam, the door should 
           stop and reverse to the fully open position.

Perform the check as follows:

s

– Check for obstruction.
– Check alignment.
– Verify wire routing from STBs to STB connection 

in powerhead.

– Check for signal interference 

Safe-T-Beam® unit (For multiple door installations).

from another. 

s

– Check wiring and wire connections.

If you have any questions, please do not hesitate to 

contact customer service at: 1-800-35-GENIE or visit

1.  READ AND FOLLOW ALL INSTRUCTIONS.
2.  Never let children operate or play with the door controls.

  Keep the remote away from children.

3.  Always keep the moving door in sight and away from people

and objects until the door is completely closed.  NO ONE 

.

R

O

O

D

 

G

N

I

V

O

M

 

E

H

T

 

F

O

 

H

T

A

P

 

E

H

T

 

S

S

O

R

C

 

D

L

U

O

H

S

4.  NEVER GO UNDER A STOPPED, PARTIALLY OPEN DOOR.
5.  Test opener monthly.  The door MUST reverse on contact

with a 1-1/2" high object (or a 2" x 4" board laid flat) at the 

center of the doorway on the floor.  After adjusting either the 

force or the limit of travel, retest the door opener.  Failure to
adjust the opener properly may cause severe injury or death.

6.  When possible, use the emergency release only when the 

door is closed.  Use caution when using this release 

door open

with the

.  Weak or broken springs are capable of increasing  

the rate of door closure and increasing the risk of severe 
injury or death.

7.  KEEP DOORS PROPERLY BALANCED.  See your garage door 

Owner’s Manual.  An improperly balanced door increases the 

risk of severe injury or death.  Have a trained door system 

technician make repairs to cables, spring assemblies, and 
other hardware.

8.  

www.geniecompany.com.

 

 

s

 ,

s

t

e

k

c

a

r

b

 ,

s

e

l

b

a

c

 ,

s

g

n

i

r

p

s

(

 

e

r

a

w

d

r

a

h

 

r

o

o

d

 

e

g

a

r

a

G

  

pulleys, etc.) are under extreme pressure and 
tension.

s   

DO NOT attempt to repair or adjust door springs or 

any hardware, and DO NOT OPERATE garage door

 automatically or manually if door is improperly

 balanced or springs are broken.

–  CONTACT A TRAINED DOOR SYSTEM TECHNICIAN.

Basic monthly maintenance tasks.

 

 

Use wall console supplied with opener.  Other approved wall 
consoles may be available. Unapproved or incompatible wall 

consoles can cause the opener to operate unexpectedly. 

s

Lubricate door rollers, bearings and hinges:

OPENER

3’ - 4’

Sectional Door 

3’ - 4’

One-Piece Door