Bosch TES 50129 RW ユーザーズマニュアル

Robert Bosch Hausgeräte GmbH

4.  Lift the water tank lid (17).

5.  Remove and rinse the water tank (16) 

and fill it with fresh cold water. Do not fill 

above the 

max mark.

6.  Replace the water tank (16) and push it 

firmly downwards into place.

7.  Close the water tank lid (17). 

8.  Fill the bean container (1) with coffee 

beans (for preparation using ground 

coffee see „Preparation using ground 

coffee“ on page 13).

9.  Press the power on/off switch 

O / I (9) to 

switch on the appliance. LED 

D

 flashes 

and LED 

F

 lights up.

10. Place a container under the milk frother 

outlet (6). 

11. Carefully pull out the milk frother (6) 

to open it. The appliance rinses out 

the milk frother (6) with water. LED 

F

 

flashes.

12. When LED 

F

 lights up constantly, 

press in the milk frother (6) to close it. 

The appliance heats up and rinses. Some 

water will run out of the coffee outlet. When 

buttons 

A

 (12), 

B

 (11) and 

C

 (10) light 

up, the appliance is ready for use.

If the appliance has not been used for 

an hour, it rinses automatically and then 

switches off (the length of time can be ad-

justed, see “Settings”, “Automatic switch-off” 

on page 11). 

Exception: The appliance switches off with-

out rinsing if only hot water or steam was 

dispensed.

To switch the appliance off manually before 

this, press the service button (12). The ap-

pliance rinses and switches off.

Note: If the appliance is being used for the 

first time, the service programme has been 

run, or the appliance has not been oper-

ated for a long period, the first beverage will 

not have the full aroma and should not be 

consumed.

When the fully automatic espresso machine 

is first used, you will achieve a suitably thick 

and stable “crema” only after the first few 

cups have been dispensed.

If the appliance is in use for a long period of 

time, water droplets will form on the ventila-

tion slits. This is normal.

Using a water filter can prevent a build-up 

of limescale deposits. 

A new water filter must be rinsed before it 

can be used. To do this, proceed as follows:

1.  Press the water filter firmly into the emp-

ty water tank with the aid of the measur-

ing spoon (18).

2.  Fill the water tank (16) with water up to 

the 

max mark.

3.  Turn the rotary  

knob (13) to position 

 

4.  Press and hold buttons 

B

 (11) and 

A

 

(12) simultaneously for at least  

5 seconds. Either 

 “off” or 

 “on” 

lights up.

5.  Press the start button (10) to select “on”.

6.  Press and hold the start button (10) for 

at least 5 seconds to confirm. All of the 

LEDs light up briefly.

7.  LED 

D

 flashes and LED 

F

 lights up.

8.  Place a container with a capacity of 0.5 

litres under the milk frother outlet (6).

9.  Pull out the milk frother (6) to open it. 

LED 

F

 flashes.

10. Water will now flow through the filter and 

rinse it.

11. When LED 

F

 lights up constantly, 

press in the milk frother (6) to close it.

12. Empty the container. 

The appliance is ready to use again.

TES501_Heft1_RW.indb   10

14.09.2011   16:10:24