Canon ir2016, ir2020 マニュアル

7

iR2016J / iR2016 / iR2020 /  / iR2016i / iR2020i

T-3-3

iR2016J / iR2016 / iR2020 /  / iR2016i / iR2020i

T-3-4

iR2016J / iR2016 / iR2020 /  / iR2016i / iR2020i

T-3-5

iR2016J / iR2016 / iR2020 /  / iR2016i / iR2020i

T-3-6

1118

Door open jam

SR202, 
SR203, 
SR209, 
SW2, SW3

The door was opened when there was printing paper in the transport 
path.

0130

Delayed feed jam

PI5

The inlet sensor is not turned on within the specified time after 
reception of a paper ejection signal from the host machine.

0231

Staying paper jam

PI5

The inlet sensor is not turned off even if paper is fed by the specified 
distance after the leading edge of the paper from the host machine 
has passed through the sensor.

0033

Stack ejection jam

PI1

When a paper stack is ejected, the HP sensor is not turned off within 
the specified time.

0035

Staple jam 

Stapler HP 
sensor 
(built in 
stapler)

The stapler HP sensor was turned off once after start of stapler 
operation, but the HP has not been reached within the specified 
time.

1036

Power-on jam 

PI5

The inlet sensor detected paper at power-on.

1137

Door open jam

SW1

The front cover switch detected opening of the front cover during 
standby or copy operation.

0000

Unknown jam

-

Other errors

0007

Initial stationary

PI6,PI7,PI8 Paper is detected in the transport path before the DADF starts initial 

operation.  

0008

Read sensor delay

PI7,PI8

The read sensor does not detect paper when the paper has been fed 
by the predetermined distance since reception of a pickup request. 

0009

Read sensor stationary

PI7

The trailing edge of paper is not detected when the paper has been 
fed by the predetermined distance since detection of it by the read 
sensor.  

000a

Paper absence (Pull out 
the document.)

PI11

The Document set sensor  has been held off since start of pickup. 

000c

Delivery reversal sensor 
delay

PI6,PI7

The delivery reversal sensor does not detect paper since the paper 
has been fed by the predetermined distance since the read sensor 
was turned on.

000d

Delivery reversal sensor 
stationary

PI6

The trailing edge of paper is not detected when the paper has been 
fed by the predetermined distance since the delivery reversal sensor 
detected the paper.

000e

ADF cover open

PI10

The feeder cover was opened during operation (of the drive system).

000f

User ADF open

sensor of 
the reader 
unit

The ADF was opened during operation (of the drive system).

0010

Pickup NG

-

The registration sensor has been held off since paper pickup started.

0120

Delay jam at duplex 
paper sensor 1

SR1002

The duplex paper sensor 1 does not turn on within the specified 
time after the delivery sensor on the main unit side turns on.

0124

Delay jam at duplex 
paper sensor 2

SR1003

The duplex paper sensor 2 does not turn on within the specified 
time after the duplex reverse motor starts.

0221

Stationary jam at 
duplex paper sensor 1

SR1002

- The duplex paper sensor 1 does not turn off when the specified 
time has lapsed since the duplex paper sensor 2 turned on.
- The duplex paper sensor 1 does not turn off when the paper 
with a longitudinal length of 280 mm reaches the standby 
position (about 90 mm from the duplex paper sensor 2). 

0228

Stationary jam at 
duplex paper sensor 2

SR1003

The duplex paper sensor 2 does not turn off when the specified 
time has lapsed since the feed motor started.

010e

Delay jam at No.2 
delivery section

SR1101

The No.2 delivery sensor does not detect presence of paper within 
the specified time after turning on of the fixing delivery sensor.