lift-master spswin 4.0 ユーザーズマニュアル
Entering and Editing Unit Data
Page 44 of 69
Doc 6001647, Rev B
Messages
From the Unit Definition Window, select the Messages
tab to display the messages page (see Figure 51). Use
this page to select and edit unit messages.
tab to display the messages page (see Figure 51). Use
this page to select and edit unit messages.
Messages can be programmed automatically
by selecting the appropriate unit model and
clicking on the Defaults button.
by selecting the appropriate unit model and
clicking on the Defaults button.
You can convert the instructions messages to
the language required for your installation site,
but we do not recommend changing the
content of the instruction messages unless
your application requires special instructions.
the language required for your installation site,
but we do not recommend changing the
content of the instruction messages unless
your application requires special instructions.
Note: It is extremely important that you select
the correct display type for your unit.
Selecting the wrong display type may cause
user-defined messages to be incorrect or
scrambled.
the correct display type for your unit.
Selecting the wrong display type may cause
user-defined messages to be incorrect or
scrambled.
Figure 51: Unit Definition Window Messages Page
E
DITING A
M
ESSAGE
1. Setting messages for Multi-Link chains is the
same as for stand-alone units, except that the
Multi-Link Message page has a Units Box.
The user must select the unit that he wishes to
address, select the correct display type, and
then change any messages desired.
Multi-Link Message page has a Units Box.
The user must select the unit that he wishes to
address, select the correct display type, and
then change any messages desired.
2. Select Model: Click on the arrow and the
menu will drop down. Click on the appropriate
display size and the menu will roll up and
display your selection:
display size and the menu will roll up and
display your selection:
Display Size/Unit:
< none >
< none >
For units without displays
Small:
2 lines x 16 characters
Medium:
2 lines x 20 characters
Large: (Sharp)
Large: (Optrex)
Large: (Optrex)
3. Select Message: Click on the arrow and the
menu will drop down. Click on the desired
message type (see below). The menu will roll
up and display your selection, and the
message content will be displayed in the Edit
Message Content field.
message type (see below). The menu will roll
up and display your selection, and the
message content will be displayed in the Edit
Message Content field.
4. Edit Message Content: To edit message
content, select row to edit by moving the
cursor over either the Top or Bottom field.
When the cursor turns into a down-pointing
arrow, click the mouse button and the desired
field will be highlighted. Make your changes,
then select the other field.
cursor over either the Top or Bottom field.
When the cursor turns into a down-pointing
arrow, click the mouse button and the desired
field will be highlighted. Make your changes,
then select the other field.
5. To preview your message, click on the Play
Message button. The message will appear on
the dark blue field below the Edit Message
Content field for several seconds, then blank.
the dark blue field below the Edit Message
Content field for several seconds, then blank.
6. To select and edit additional unit messages
return to Step 2.
7. Save your messages by clicking on either the
Apply or Done buttons at the bottom of the
window.
window.
Important Note: The display type for Infinity
and Multi-Link units must be selected before
connecting with a unit.
and Multi-Link units must be selected before
connecting with a unit.
M
ESSAGE
T
YPES
Welcoming Message: Also referred to as the "Banner" message, the Welcoming Message is displayed
when a visitor is not using the system. It should greet visitors and tell them where they are (e.g.,
Welcome to Seashore Apartments).
when a visitor is not using the system. It should greet visitors and tell them where they are (e.g.,
Welcome to Seashore Apartments).
Instructions Message: This message provides instructions for system use.
After Dialing Message: This message provides the user with instructions about what to do while the
system is dialing and after the conversation.
system is dialing and after the conversation.
All Other Messages: These messages are used to prompt and direct the user through various steps of
the system. Unless your application requires it, we strongly advise against changing any of the
remaining messages not previously discussed.
the system. Unless your application requires it, we strongly advise against changing any of the
remaining messages not previously discussed.