Panasonic KX-MB2575 操作ガイド
Feature
Code
Selection
Font source in
PCL
PCL
#768
“DOWNLOAD FONT” can be selected after the downloaded font is registered to the
unit.
M1N “RESIDENT” (default): The document will be printed using resident font.
M2N “DOWNLOAD FONT”: The document will be printed using download font.
unit.
M1N “RESIDENT” (default): The document will be printed using resident font.
M2N “DOWNLOAD FONT”: The document will be printed using download font.
Font number in
PCL
PCL
#769
To set the font number to be used in PCL printing. The unit assigns a number to
each font.
1. MtN A MBNM7NM6NM9N A MOKN
2. Enter the font number from “000” to “054”, using the dial keypad.
each font.
1. MtN A MBNM7NM6NM9N A MOKN
2. Enter the font number from “000” to “054”, using the dial keypad.
R The default setting is “000”.
3. MOKN A MtN
Note:
R If the font source in PCL (feature #768 on page 88) is set to “DOWNLOAD
R If the font source in PCL (feature #768 on page 88) is set to “DOWNLOAD
FONT”, the default setting is “001”.
Font pitch/point in
PCL
PCL
#770
To set the font pitch/point to be used in PCL printing.
1. MtN A MBNM7NM7NM0N A MOKN
2. Enter the font pitch from “00.44” to “99.99”, or the point from “004.00” to
1. MtN A MBNM7NM7NM0N A MOKN
2. Enter the font pitch from “00.44” to “99.99”, or the point from “004.00” to
“999.75”, using the dial keypad.
R The default pitch is “10.00” and the default point is “012.00”.
R Whether this step is font pitch or point depends on the font number
R The default pitch is “10.00” and the default point is “012.00”.
R Whether this step is font pitch or point depends on the font number
selected in feature #769 (page 88).
3. MOKN A MtN
Symbol set in
PCL
PCL
#771
To set the symbol set to be used in PCL printing.
1. MtN A MBNM7NM7NM1N
2. Press MCN or MDN repeatedly to display the desired symbol set. A MOKN
1. MtN A MBNM7NM7NM1N
2. Press MCN or MDN repeatedly to display the desired symbol set. A MOKN
A MtN
Line breaks in
PCL
PCL
#772
To set each behaviour when receiving CR, LF, and FF codes.
M1N “CR/LF/FF” (default): CR=CR, LF=LF, FF=FF
M2N “CR+LF/LF/FF”: CR=CR+LF, LF=LF, FF=FF
M3N “CR/CR+LF/CR+FF”: CR=CR, LF=CR+LF, FF=CR+FF
M1N “CR/LF/FF” (default): CR=CR, LF=LF, FF=FF
M2N “CR+LF/LF/FF”: CR=CR+LF, LF=LF, FF=FF
M3N “CR/CR+LF/CR+FF”: CR=CR, LF=CR+LF, FF=CR+FF
Auto continue
mode
mode
#773
To set the length of time before the unit recovers if a memory overflow occurs.
M1N “OFF” (default)
M2N “20s”
M3N “30s”
M4N “60s”
M5N “90s”
M6N “120s”
M1N “OFF” (default)
M2N “20s”
M3N “30s”
M4N “60s”
M5N “90s”
M6N “120s”
Data timeout
#774
To change the data timeout setting. The unit will automatically print the remaining
data in memory when the computer does not send data to the unit during the set
time.
1. MtN A MBNM7NM7NM4N A MOKN
2. Enter the desired data timeout setting from “005” seconds to “600” seconds,
data in memory when the computer does not send data to the unit during the set
time.
1. MtN A MBNM7NM7NM4N A MOKN
2. Enter the desired data timeout setting from “005” seconds to “600” seconds,
using the dial keypad.
R The default setting is “060” seconds.
R The default setting is “060” seconds.
3. MOKN A MtN
88
10. Programmable Features