Zvox SoundBar SB500 オーナーマニュアル
RESET Indication.
Master Reset
A master reset restores a SB400/SB500
to the factory default behavior. It erases
any “learned” remote control response. It
sets the SURROUND mode to Surround
“2”, sets OUTPUT LEVELING and DIALOG
EMPHASIS to OFF and sets BASS and
TREBLE to no boost or cut in bass or treble
output. It sets the INPUT to Optical Input 1.
to the factory default behavior. It erases
any “learned” remote control response. It
sets the SURROUND mode to Surround
“2”, sets OUTPUT LEVELING and DIALOG
EMPHASIS to OFF and sets BASS and
TREBLE to no boost or cut in bass or treble
output. It sets the INPUT to Optical Input 1.
To perform the Master Reset, first put the
SB400/SB500 in Standby mode by pressing
the POWER button on the SB400/SB500
remote control. When you see “OFF” on the
SB400/SB500 display, the unit is in Standby.
You can also put a SB500 in Standby by
pressing down on the end panel MUTE
button for about 5-7 seconds.
SB400/SB500 in Standby mode by pressing
the POWER button on the SB400/SB500
remote control. When you see “OFF” on the
SB400/SB500 display, the unit is in Standby.
You can also put a SB500 in Standby by
pressing down on the end panel MUTE
button for about 5-7 seconds.
Once the SB400/SB500 is in Standby,
locate the INPUT button on the end panel
of the SB400/SB500. (You cannot use the
INPUT button on the remote to perform a
Master Reset.)
locate the INPUT button on the end panel
of the SB400/SB500. (You cannot use the
INPUT button on the remote to perform a
Master Reset.)
Press and hold down the end panel INPUT
button for about 15 to 20 seconds. When
you see the three letters “
button for about 15 to 20 seconds. When
you see the three letters “
r S t ” appear
on the display (see figure below), release the
INPUT button. The SB400/SB500 will then
show the four-digit firmware code number and
turn “ON”. The master reset is complete.
INPUT button. The SB400/SB500 will then
show the four-digit firmware code number and
turn “ON”. The master reset is complete.
SB400/SB500 Wall Mounting
Information
Information
The SB400/SB500 has two keyhole mounting
sites on its back panel. You can mount the
SB400/SB500 onto two screwheads using
these mounting sites. The SB400/SB500
weighs 16 pounds. NOTE: It is the installer’s
responsibility to ensure the screws are installed
into the wall or other surface securely and
that the screwheads are the correct size for
the hanger mounts on the rear of the SB400/
SB500. ZVOX Audio recommends your
mounting sites be able to support at least
twice the weight of the SB400/SB500.
sites on its back panel. You can mount the
SB400/SB500 onto two screwheads using
these mounting sites. The SB400/SB500
weighs 16 pounds. NOTE: It is the installer’s
responsibility to ensure the screws are installed
into the wall or other surface securely and
that the screwheads are the correct size for
the hanger mounts on the rear of the SB400/
SB500. ZVOX Audio recommends your
mounting sites be able to support at least
twice the weight of the SB400/SB500.
+HLJKWPP
6%
6%
'HSWKPP
PP
PP
LQSXW
SDQHO
LQSXW
SDQHO
PP
IURQW
+HLJKWPP
'HSWKPP
PP
PP
PP
IURQW
Back view with dimensions of the SB500 and SB400