VECTRIX CORPORATION GC667894 ユーザーズマニュアル
Transmitter (Digimatic) Operations Manual
2015.11
*4 Notice:
Available ＩＤ No. may be limited if you use measuring
equipment which has limited measuring range.
equipment which has limited measuring range.
For measuring equipment having origin & preset function,
larger number than measured number can be set as ID.
Please see the instruction of each measuring equipment.
larger number than measured number can be set as ID.
Please see the instruction of each measuring equipment.
Reset of Transmitter；
In case of malfunction, but the battery has voltage(3.0V or
more), please rest the Transmitter.
・
more), please rest the Transmitter.
・
Remove the battery
See 3.1 1)
・
While pushing 3 SW's. (CANCEL, ID No. and DATA)
at a same time, insert battery., then buzzer sounds “Pi”,
“Pi”, “Pi”,
“Pi”, “Pi”,
※
After the reset ID No.=0, Receiver No.=1 (at shipping)
Guarantee
----- Guarantee rule -----
This product is manufactured under strict quality control.
If trouble due to our manufacture or transportation occurred to
product within 6 months, we will repair it free of charge.
In the following cases, repair will be charged even within the
period of guarantee.
・
Trouble due to misuse or improper handling
・
Trouble due to the remodeling by customer
・
Change in the appearance such as scratch during the use
・
Trouble due to inevitability such as fire earthquake, flood or
due to abnormal voltage.
・
This guarantee is valid only in Japan.
＜
To Agent＞
Please fill & sign the above “Guarantee”, then give it to customer.
＜
High-performance Function＞
（
In case of normal usage without High-performance Function
using one receiver, please skip it.） Multi-settings among Item2
～
～
Item4 are unavailable. Except Item2 setting of receiver
DR-200 side is necessary.
１．
Setting of Receiver No.
(Multi-receiver use)
If you use more than one receiver in one area, to avoid radio
interference you can set Receiver No. to each transmitter.
Receiver No. is chosen from 1～128.
Receiver No. is chosen from 1～128.
Operation:
①
Let measuring equipment show numeric where the integer
should be Receiver No. which you want to set.
should be Receiver No. which you want to set.
②
While pushing C Sw., push ID Sw.
After completed setting, buzzer sounds “Pi”.
After completed setting, buzzer sounds “Pi”.
*5 Default(Shipment) Receiver. No.=1
*6 Operation for receiver ＤＲ-200Ｕ/Ｒ is required.
*6 Operation for receiver ＤＲ-200Ｕ/Ｒ is required.
（
Look at the operation manual of ＤＲ-200Ｕ/Ｒ.）
２．
Interval Transmission
TXG- has function to transmit data every specified time.
２．１
Setting
①
Interval active : Let measuring equipment show “0.2”.
Then while pushing C Sw., push ID Sw.
The confirmation is checked by buzzer sounds “Pi”.
The confirmation is checked by buzzer sounds “Pi”.
②
Interval time : Let measuring equipment show “0.00～0.16”.
Then while pushing C Sw., push ID Sw.
Then while pushing C Sw., push ID Sw.
③
Interval cancel : Let measuring equipment show “0.3”.
Then while pushing C Sw, push ID Sw.
Interval function
Display
Interval function
Display
①
Active
0.2
③
Cancel
0.3
Interval time
Display
Interval time
Display
Min. (appr. 0.4sec.)
0.00
1min.
0.11
1sec.
0.01
2min.
0.12
2sec.
0.02
5min.
0.13
5sec.
0.03
10min.
0.14
10sec.
0.04
30min.
0.15
30sec.
0.05
60min.
0.16
*7 Minimum time depends on measuring equipment.
*8
*8
Number under place of above “Display” is ignored.
(Ex.0.039)
２．２
Transmission start and halt
①
Start Push DATA Sw. of transmitter, then sounds “Pi”.
(By DATA Switch of cable side it does not work.)
②
Halt
Push C Sw. Then buzzer sounds “Pi”.
*9 During interval setting, cancel function does not work.
*10 For change of interval time、please set again after halt by
*10 For change of interval time、please set again after halt by
C Sw. or cancel of interval function.
Name・Type
Transmitter TXG－
Serial No.
Period of guarantee
6 months from purchased date
Date purchased
Day
Month
Year
u
st
om
er
Company
Address
Address
〒
Division
Name
TEL.
Name
TEL.
Agent (Company, Address, Tel., Name )
(Signature)