Gait Up PHYS5POMOC ユーザーズマニュアル
12 June 2017 - Physilog5usermanual.pdf-v1.2.3 - Check www.gaitup.com for the latest version. Copyright 2017 Gait Up SA. CH-1015 SWITZERLAND
4
1) Start the sensors with the main button (like for standalone measurement above). One of
the sensors (Master) will start to blink green, the others (Slaves) shine green and don't record
until they receive the synchronization signal from the Master sensor.
2) Once the sensors are synchronized, they blink green synchronously with the Master
sensor and record.
3) To stop the measurement, press the main button of the Slave sensors. They shine green
until they have received the final synchronization information from the Master. The Master
must be turned off as last, after all the Slave sensors have turned off the green LED.
To start a Slave sensor without receiving the signal from the Master, shortly press the main
button when it is shining green, the sensor will start the measurement without being
synchronized to other sensors. To stop slave sensors without waiting for Master
synchronization, shortly press the main button again when the LED is shining green after
turning off the recording.
the sensors (Master) will start to blink green, the others (Slaves) shine green and don't record
until they receive the synchronization signal from the Master sensor.
2) Once the sensors are synchronized, they blink green synchronously with the Master
sensor and record.
3) To stop the measurement, press the main button of the Slave sensors. They shine green
until they have received the final synchronization information from the Master. The Master
must be turned off as last, after all the Slave sensors have turned off the green LED.
To start a Slave sensor without receiving the signal from the Master, shortly press the main
button when it is shining green, the sensor will start the measurement without being
synchronized to other sensors. To stop slave sensors without waiting for Master
synchronization, shortly press the main button again when the LED is shining green after
turning off the recording.
3.2 Start measurement from tablet
The companion Android application allows to start Physilog®5. Two modes are available in
the application, for details refer to the user manual of the Android application. There is no
need to pair your Physilog® with the tablet prior to Bluetooth communication, just select
the Physilog® from the list in the app. If the sensor is not detected by the tablet, shortly
press the main button to enter detection mode. If the sensor can still not be connected,
check that it has enough battery and plug and unplug the sensor to a computer.
the application, for details refer to the user manual of the Android application. There is no
need to pair your Physilog® with the tablet prior to Bluetooth communication, just select
the Physilog® from the list in the app. If the sensor is not detected by the tablet, shortly
press the main button to enter detection mode. If the sensor can still not be connected,
check that it has enough battery and plug and unplug the sensor to a computer.
Briefly, the first mode one is called “Signals Visualizer”, it can be used to check if the
sensor's data looks as expected. Up to 4 sensors can be connected to the application at the
same time for this mode. The “Signals Visualizer” starts displaying data from connected
sensors automatically (no start button). It does not store the data, neither on the tablet nor
on the Physilog®. During the measurement, the Physilog®5 blinks green where each blink
is made of two short flashes. To stop data streaming either disconnect the sensor or exit
this part of the application.
sensor's data looks as expected. Up to 4 sensors can be connected to the application at the
same time for this mode. The “Signals Visualizer” starts displaying data from connected
sensors automatically (no start button). It does not store the data, neither on the tablet nor
on the Physilog®. During the measurement, the Physilog®5 blinks green where each blink
is made of two short flashes. To stop data streaming either disconnect the sensor or exit
this part of the application.
The second mode is called “File Transfer” and allows to start and stop data recording of the
Physilog® of up to two sensors at the same time. When pushing the “Start measurement”
button, the connected Physilog start recording and sending the data file to the tablet.
When launching two Physilog®5 at the same time using the tablet application they can be
synchronized in post-processing in Matlab.
Physilog® of up to two sensors at the same time. When pushing the “Start measurement”
button, the connected Physilog start recording and sending the data file to the tablet.
When launching two Physilog®5 at the same time using the tablet application they can be
synchronized in post-processing in Matlab.