Gait Up PHYS5POMOC ユーザーズマニュアル
12 June 2017 - Physilog5usermanual.pdf-v1.2.3 - Check www.gaitup.com for the latest version. Copyright 2017 Gait Up SA. CH-1015 SWITZERLAND
6
5.2 Handling / Maintenance
Physilog®5 should be handled carefully. In particular, it should not receive shocks, such as
fall, crushing, being hit etc. Do not press too hard on the on/off button, this can damage the
button.
fall, crushing, being hit etc. Do not press too hard on the on/off button, this can damage the
button.
Warning: Do not use or charge the Physilog® if the sensor or its case is damaged.
Contact Gait Up about what further action is needed when the case is damaged.
In case the battery is damaged immediately move the device away from
flammable materials and contact Gait Up's customer support.
Contact Gait Up about what further action is needed when the case is damaged.
In case the battery is damaged immediately move the device away from
flammable materials and contact Gait Up's customer support.
- To benefit from the maximal battery life, fully charge Physilog® sensors before doing
measurements (LED shines green when connected to computer or charger, you can also
check with the App).
- Copy trial recordings to your computer: Physilog® is not the best place to keep important
data.
- Physilog®5 can be used outside. But do not use Physilog®5 to measure water-sport
activities without additional waterproofing.
measurements (LED shines green when connected to computer or charger, you can also
check with the App).
- Copy trial recordings to your computer: Physilog® is not the best place to keep important
data.
- Physilog®5 can be used outside. But do not use Physilog®5 to measure water-sport
activities without additional waterproofing.
- Do not introduce pointy objects into the small hole besides the USB entry, this irreversibly
damages the waterproofing of the sensor.
- Storage: Store in a cool (0°C – 30°C) and dry place. The provided box is the perfect place for
your sensor.
- Cleaning: Sensors can be cleaned gently using alcohol wipes. Before you clean the device
make sure it is turned off and disconnect all cables. Alcohol used in excess may damage the
sensor’s waterproofing. Make sure to use wipes and not put liquid alcohol directly on the
sensor.
- Sensors do not need yearly recalibration.
- Do not throw Physilog® sensors in the normal trash, dispose of it properly considering local
laws and rules about electronic waste and batteries. Contact Gait Up's customer support for
more information about elimination of Physilog®.
- Make sure to know which Physilog® file corresponds to which trial for your analysis – First
digits of file name are automatically incremented for each day of measurement (exceeding
999 and firmware update resets the increment back to 001). Note that date of file
generation (recorded between one start and stop of the Physilog®) is visible in the XLS or
CSV file and the Matlab structure “header”. If you wish to adapt internal date and time of
the Physilog®, read section below.
- Do not remove the “conf.bin” file from the Physilog, otherwise it will create empty files (no
sensor activated). If this happens, recreate a configuration in the Research ToolKit software
or contact Gait Up's customer support.
damages the waterproofing of the sensor.
- Storage: Store in a cool (0°C – 30°C) and dry place. The provided box is the perfect place for
your sensor.
- Cleaning: Sensors can be cleaned gently using alcohol wipes. Before you clean the device
make sure it is turned off and disconnect all cables. Alcohol used in excess may damage the
sensor’s waterproofing. Make sure to use wipes and not put liquid alcohol directly on the
sensor.
- Sensors do not need yearly recalibration.
- Do not throw Physilog® sensors in the normal trash, dispose of it properly considering local
laws and rules about electronic waste and batteries. Contact Gait Up's customer support for
more information about elimination of Physilog®.
- Make sure to know which Physilog® file corresponds to which trial for your analysis – First
digits of file name are automatically incremented for each day of measurement (exceeding
999 and firmware update resets the increment back to 001). Note that date of file
generation (recorded between one start and stop of the Physilog®) is visible in the XLS or
CSV file and the Matlab structure “header”. If you wish to adapt internal date and time of
the Physilog®, read section below.
- Do not remove the “conf.bin” file from the Physilog, otherwise it will create empty files (no
sensor activated). If this happens, recreate a configuration in the Research ToolKit software
or contact Gait Up's customer support.