Microchip Technology MA240029 データシート
2010-2011 Microchip Technology Inc.
DS39996F-page 161
PIC24FJ128GA310 FAMILY
When the RTCC is enabled, it continues to operate with
the same clock source (SOSC or LPRC) that was
selected prior to entering V
the same clock source (SOSC or LPRC) that was
selected prior to entering V
BAT
mode. There is no pro-
vision to switch to a lower power clock source after the
mode switch.
Since the loss of V
mode switch.
Since the loss of V
DD
is usually an unforeseen event, it
is recommended that the contents of the Deep Sleep
Semaphore registers be loaded with the data to be
retained at an early point in code execution.
Semaphore registers be loaded with the data to be
retained at an early point in code execution.
10.5.1
V
BAT
MODE WITH NO RTCC
By disabling RTCC operation during V
BAT
mode, power
consumption is reduced to the lowest of all
power-saving modes. In this mode, only the Deep
Sleep Semaphore registers are maintained.
power-saving modes. In this mode, only the Deep
Sleep Semaphore registers are maintained.
10.5.2
WAKE-UP FROM V
BAT
MODES
When V
DD
is restored to a device in V
BAT
mode, it auto-
matically wakes. Wake-up occurs with a POR, after
which the device starts executing code from the Reset
vector. All SFRs, except the Deep Sleep Semaphores
and RTCC registers are reset to their POR values. If
the RTCC was not configured to run during V
which the device starts executing code from the Reset
vector. All SFRs, except the Deep Sleep Semaphores
and RTCC registers are reset to their POR values. If
the RTCC was not configured to run during V
BAT
mode,
it will remain disabled and RTCC will not run. Wake-up
timing is similar to that for a normal POR.
To differentiate a wake-up from V
timing is similar to that for a normal POR.
To differentiate a wake-up from V
BAT
mode from other
POR states, check the VBAT status bit (RCON2<0>). If
this bit is set while the device is starting to execute the
code from Reset vector, it indicates that there has been
an exit from V
this bit is set while the device is starting to execute the
code from Reset vector, it indicates that there has been
an exit from V
BAT
mode. The application must clear the
V
BAT
bit to ensure that future V
BAT
wake-up events are
captured.
If a POR occurs without a power source connected to
the V
If a POR occurs without a power source connected to
the V
BAT
pin, the VBPOR bit (RCON2<1>) is set. If this
bit is set on a POR, it indicates that a battery needs to
be connected to the V
be connected to the V
BAT
pin.
In addition, if the V
BAT
power source falls below the
level needed for Deep Sleep Semaphore operation
while in V
while in V
BAT
mode (e.g., the battery has been
drained), the VBPOR bit will be set. VBPOR is also set
when the microcontroller is powered up the very first
time, even if power is supplied to V
when the microcontroller is powered up the very first
time, even if power is supplied to V
BAT
.
With VBPOR set, the user should clear it, and the next
time, this bit will only set when V
time, this bit will only set when V
DD
= 0 and the V
BAT
pin has gone below level (0.4V-0.6V).
10.5.3
I/O PINS DURING V
BAT
MODES
All I/O pins should be maintained at V
SS
level; no I/O
pins should be given V
DD
) during V
BAT
mode. The only exceptions are
the SOSCI and SOSCO pins, which maintain their states
if the secondary oscillator is being used as the RTCC
clock source. It is the user’s responsibility to restore the
I/O pins to their proper states, using the TRIS and LAT
bits, once V
if the secondary oscillator is being used as the RTCC
clock source. It is the user’s responsibility to restore the
I/O pins to their proper states, using the TRIS and LAT
bits, once V
DD
has been restored.
10.5.4
SAVING CONTEXT DATA WITH THE
DSGPRn REGISTERS
DSGPRn REGISTERS
As with Deep Sleep mode, all SFRs are reset to their
POR values after V
POR values after V
DD
has been restored. Only the
Deep Sleep Semaphore registers are preserved. Appli-
cations which require critical data to be saved should
save it in DSGPR0 and DSGPR1.
cations which require critical data to be saved should
save it in DSGPR0 and DSGPR1.
The BOR should be enabled for the reliable operation
of the V
of the V
BAT
.
Note:
If the V
BAT
mode is not used, the
recommendation is to connect the V
BAT
pin to V
DD
.
When the V
BAT
mode is used (connected
to the battery), as well as when it is not
used, it is always recommended to
connect a 0.1 µF capacitor from the V
used, it is always recommended to
connect a 0.1 µF capacitor from the V
BAT
pin to ground. The capacitor should be
located very close to the V
located very close to the V
BAT
pin.