Tascam CC-222MKIV ユーザーズマニュアル

1 – Introduction

TASCAM CC-222

6 – After recording

Erasing tracks

It is possible to erase the last recorded track, the last two

recorded tracks, the last three recorded tracks, etc. It is not,

however, possible to erase tracks in the “middle” of the disc.

CAUTION

This operation cannot be undone. If you are going
to erase a track or tracks, make sure that they are
recordings that you really want to erase!

NOTE

To operat this function, the unit should be in Continue
mode. The function cannot to be used when play-
back mode is Single, Random or Program. If erasing
is attempted in such modes, Cannot ERASE! will be
displayed.

1 With the disc loaded, and the unit in stop mode,

press the

ERASE

key.

2 If the display does not show

ERASE XX-XX?

, where

XX-XX

is the number of the last track recorded on

the disc, turn the

MULTI DIAL

or use the

SKIP

keys

until it is displayed.

3 Turn the

MULTI DIAL

or use the

SKIP

keys to change

the number of the first track to be erased. The

highest value that this number can take is the last

track recorded (for example, if 17 tracks have been

recorded on the disc, 17-17 means that the last track

only, number 17, will be erased). The lowest value

that this number can take is 2 (if this number was 1,

the whole disc would be erased, as described below).

If you do not want to proceed with the erase opera-

tion, press the

ERASE

key or

STOP

key.

NOTE

If only one track has been recorded on the disc, only
the “erase disc” option (see “Erasing a whole disc” on
page 29) is available.

4 When the range of tracks to be erased has been

selected, press the

MULTI DIAL

or the

ENTER

key.

If the erase operation has been selected, the word

ERASE

flashes on the display, and the timer starts counting down.
At the end of the countdown period, the word

Complete

appears briefly on the display, and the display returns to

the track/time display.

Erasing a whole disc

When you want to erase a whole disc (all the tracks on a

disc), follow the procedure below:
1 With the disc loaded, and the unit in stop mode,

press the

ERASE

key.

2 Turn the

MULTI DIAL

or use the

SKIP

keys until the

display shows

ERASE DISC?

If you do not want to proceed with the erase opera-

tion, press the

ERASE

key or

STOP

key.

3 To erase the contents of the disc, press the

MULTI

DIAL

or the

ENTER

key.

NOTE

This operation cannot be undone. If you are going to
erase a disc, make sure that it contains only record-
ings that you really want to erase!

If the erase operation has been selected, the word

ERASE

flashes on the display, and the timer starts

counting down a time value shown on the display.

At the end of the countdown period, the word

Com-

plete

appears briefly on the display, and the dis-

play returns to the track/time display.

Refreshing a disc

If a CD-RW disc has been corrupted at any point (e.g.

power has been cut off in the middle of a finalize opera-

tion, etc.), or has been used in a computer or another piece

of equipment that makes it unreadable, it is possible to

“refresh” the disc to make it usable again.
1 With the disc loaded, and the unit in stop mode,

press the

ERASE

key.

2 Turn the

MULTI DIAL

or use the

SKIP

keys until the

display shows

DISC REFRESH?

3 To refresh the disc, press the

MULTI DIAL

or the

ENTER

key.

If you do not want to proceed with the refresh op-

eration, press the

ERASE

key or

STOP

key.

NOTE

This operation cannot be undone. If you are going to
refresh a disc, make sure that it contains only record-
ings that you really want to erase!

If the refresh operation has been selected, the words

ERASE XX:XX

are shown on the display, and the

timer starts counting down.

At the end of the countdown period, the word Com-

plete appears briefly on the display, and the display

returns to the track/time display (of course, there

are no tracks, and the disc is at the start, with the

total time of the disc available for recording).