Tascam CC-222MKIV ユーザーズマニュアル

1 – Introduction

TASCAM CC-222

7 – Cassette operating

Dubbing tapes from the CD deck

To record from the internal CD deck:
1 Prepare for recording as described above (load a

tape, set the REV MODE, etc.).

2 Load the source CD disc into the unit with the re-

corded side down.

3 Use the

key to set the dubbing volume to

THRU

to bypass the input level control (see “Bypass-

ing the input level for dubbing” on page 24).

If you want to adjust the input volume, set the

DUB>VOL

menu to

and use the left (tape)

INPUT

control to adjust the level of signals fed to the tape

from the CD player.

NOTE

If you want to record the tracks on the tape in a differ-
ent order from those on the disc, use the programmed
playback mode to rearrange the tracks (see “Program
playback” on page 17). Leave the disc in stop mode
when you have finished programming the order.

4 Press the

DUB 2

key.

If the tape is in stop mode,

the tape rewinds to the

beginning of the current side.

At the start of the tape, recording starts, but the CD

does not start playback for eight seconds. The

DUB

indicator flashes.

The CD starts playback after the eight seconds at

the start of the cassette. The

DUB

indicator lights

steadily.

If the tape is in record standby mode,

recording

starts immediately, and the CD starts playback im-

mediately. The

DUB

indicator lights.

The dubbing stops when playback reaches the end of the

CD, or when the tape reaches the end of its run (one side in

the case of single-sided (

) reverse mode, both sides in

the

reverse mode), whichever comes first.

Note that if the tape is set to auto-reverse, and the last item

recorded on one side of a tape was not completely recorded

before the tape was reversed, that item will be automati-

cally repeated.
Also note that when the tape automatically reverses, eight

seconds are used as non-recorded time at the beginning

of the second side (the tape is in record mode, but the CD

does not play back), again to allow for leader tape at the

start of the cassette.
The dubbing process can also be stopped manually with

the

STOP

key of the cassette deck or the CD deck. All

other transport keys are disabled.

NOTE

Dubbing is not possible if a cassette is not loaded, or
a CD is not loaded. It is not possible if the cassette is
write-protected, or if the CD is a recordable disc which
does not currently have any material recorded on it.

It is also not possible to enter the dubbing mode if the
tape is not in stop or record standby mode, or if the CD
is not in stop or pause mode.

Recording operations

Recording pre-recorded tapes, records, or other pub-lished

or broadcast material may infringe copyright laws. Check

before recording.
1 Set the

REV MODE

switch.

If you want to make a bi-directional recording, set

the

REV MODE

switch to the

position.

Set to the

position if recording is to be made on

a single side of the tape.

2 Load a recordable cassette. Check that the safety

tabs on the spine of the cassette are in place. If they

have been broken off, block the holes with adhesive

tape.

3 Press the

INPUT 2 SEL

key to select either

LINE2

DISC

as a recording source.

When

DISC

is selected, the built-in CD player’s out-

put is selected as a source.

When

LINE2

is selected, the external signal from the

LINE 2

jacks is selected as a source.

4 Press the

RECORD

key. The deck enters record

standby mode and the indicators light up.

5 Play back the source, and adjust the recording level

using the tape deck’s

INPUT

level control so that

the loudest sound makes the meters briefly reach

around the “0 dB” point for normal or high-position

tapes (recording is not possible with metal tapes).

6 Press either the

PAUSE

PLAY

key to start recording.

To stop recording temporarily, press the

PAUSE

key. To restart recording, press either the

PAUSE

key or

PLAY

keys. If the

PLAY

key whose indica-

tor is unlit is pressed, the recording direction will

reverse, and the

PLAY

key must be pressed again to

restart recording.

7 To stop recording, press the

STOP

key.