Generac Power Systems H-100 사용자 설명서

Dump Enable — Indicates if extra load dump gov-

ernor compensation is desired to reduce increase 
in frequency caused by drop in load. The following 
three selections are available:

-  No Dump — No additional compensation.
- Dump — Reset governor algorithm when load 

dump detected.

-  Dump & Hold — Same as Dump, but also hold 

throttle closed until frequency back in range.

Engine Linearization — Selects engine torque 

to actuator position translation curve for Bosch 
Actuators.

0 = No conversion - torque = position
1 =  Butterfly Actuator with minimum position 

same as unpowered actuator

2 = Diesel arm with Horizontal rod
3 = Diesel arm with Vertical rod
4 =  Same as 1, but minimum position at actuator 

mechanical stop

5 =  Same as 4, but with limited position resolu-

tion of 1

6 =  Same as 4, but with added energy to accom-

modate throttles that normally operate in the 
nearly closed position at no load

Integral limit/Antiwindup — Choose whether to use 

an integral limit or an anti-windup strategy.

 

YES = integral limit

 

NO = anti-windup

Limit/windup parameter — If “Integral Limit” is 

selected, this is the maximum value the integral 
is allowed. If “Anti-Windup” is selected, this is the 
integral value above which the anti-windup algo-
rithm becomes active.

Pwm Counts per ampx10 — Number of PWM 

counts required to drive one tenth of an amp into 
a linear current driven actuator. This only applies 
to the “Linear Current” actuator type.

Desynch Offset — Offset of –0.9 to +0.9 Hertz to be 

applied to the target frequency to improve passive 
synchronizing by Automatic Transfer Switches. If 
an in-phase or synchronized transfer is required, 
use this setting to adjust the generator frequency 
to 0.1 Hz above nominal Utility frequency.

•

•

•

•

•

•

 NO.  PARAMETER 

UNITS

 

1  

Standby KP 

-

 

2  

Standby KI 

-

 

3  

Standby KD 

-

 4 

  QuietTest® 

KP 

-

 5 

  QuietTest® 

KI 

-

 6 

  QuietTest® 

KD 

-

 

7  

Actuator Type 

-

 

8  

Actuator Offset 

-

 

9  

Actuator Fullscale 

-

  10  

Actuator Normal Start Position 

-

  11  

Actuator QuietTest® Start Position 

-

  12  

Soft Start Time 

Seconds

  13  

Soft Start Frequency 

Hz

  14  

Diesel  

Y/N

  15  

Dump Enable 

-

  16  

Engine Linearization 

-

  17  

Integral limit/Antiwindup 

Y/N

  18  

Limit / windup parameter  

-

  19  

Pwm Counts per ampx10 

-

 20  Desynch 

Offset 

Hz

Just like in the PM-DCP, there are two types of trend-
ing available - Remote  and Local.

GenLink performs remote trending by polling the 
controller for the selected data at the desired rate. 
Up to 8 analog channels can be monitored at a 0.3 
second rate. If a faster rate is desired, reducing the 
number of analog channels monitored will allow for a 
0.1 second rate. The polling rate can be varied from 
0.1 seconds to several hours. GenLink can save the 
data to a file and/or display it as a near real-time 
graph. The file is MS Excel compatible ( CSV format 
). Examples of things you can trend are the generator 
frequency response (in 0.1 second steps) to a block 
load or Generated power over a day.

‹

 

 

9