Netgear TA612V 전단

Smart Internet Phone Adapter

Add voice to your internet

INSTALLATION GUIDE

This guide shows you how to set up your Smart Internet Phone Adaptor 
with a Router or Switch instead of just a single PC. This way you can share 
your internet connection with multiple computers (i.e. via Wireless Lan).

 

a.  Unplug the power cable for your modem.

 

b.  Unplug the power cable for your router.

 

c.  Disconnect the Ethernet cable connectiong your modem to your 

 

  router from the WAN/Internet port on your router, and connect 

 

  that end of the Ethernet cable to the Internet port on the TA612V 

 

  Smart Internet Phone Adaptor.

 

d.  Connect one end of the Ethernet cable we provide into the PC 

 

  port on the TA612V. Connect the other end of this Ethernet cable 

 

  into the WAN/Internet port on your router.

 

e.  Plug the power cable back into your modem. Wait about two 

 

a.  Plug the power cable into the Power port on the TA612V Smart Internet 

 

  Phone Adaptor and into an electrical outlet. This turns on your Smart 

 

  Internet Phone Adaptor. You do not need to unplug it when not in use.

 

b.  Check that the Power light       on the Smart Internet Phone Adaptor is 

 

  illuminated. Wait at least five minutes for the phone adapter to start up. 

 

  There may be updates that need to be downloaded such as new firmware or 

 

  changes to your features. Do not interrupt the registration process by 

 

c.   The status light on the front of the TA612V will flash.  Wait two minutes 

 

d.  Plug the power cable back into your router and wait about two minutes for it 

 

  to start up before continuing.

 

e.  Connect a telephone to the TA612V Phone 1 port using the adapter provided.

 

f.   If you have a DSL modem that requires PPPoE you need to set up your PPPoE 

 

  username and password in the TA612V. Point your browser to:

 

  http://192.168.61.1/

 

  Log in using the username and password printed on the back of the TA612V. 

 

  After setup reboot your TA612V.

12VDC, 1.2A
Power

Phone 2

(inactive)

Phone 1

Restore
Factory

Settings

PC

Internet

Power

Status

Internet

PC

Phone 1

Phone 2

Blink=Activity 

Ethernet: Green=100Mbps/Amber=10Mbps

Add voice to your internet

If you have no dial tone, check the following:

• 

Make sure the phone is plugged into the proper port on the Smart 

 

Internet Phone Adaptor (phone port #1)

• 

Make sure the Internet light       on the Smart Internet Phone 

 

Adaptor is active. If not, check your connection to the Internet. Try 

 

rebooting your modem. If that does not work, contact your internet 

 

provider’s customer service.

The easiest way 
to get VoIP

 

a)  Power up the computer.

 

b) Use a Web browser to go to the bbpglobal web site, 

 

  http://www.bbpglobal.com/netgear/

 

  Follow the instructions to setup your account. During this process, 

 

  you will be asked to provide your contact information, the serial  

 

  number and the MAC address of your TA612V, shown at the back 

 

  of your unit.

 

c)  Reboot your TA612V after registration.

 

d) After reboot, pick up your telephone handset and listen for a dial 

 

  tone. If you hear dial tone then you have finished installation and 

 

  may begin making calls.  For dialing instructions, see the Helpfule 

 

  Hints on this card. If you do not hear a dial tone, see 

 

  Troubleshooting. For more tips about troubleshooting, see the 

 

  User Manual.

 

e)  (Optional) You may also select a PSTN number to receive phone 

 

  calls. Please go to the following web site to select a PSTN number. 

 

  Please note there is an additional charge for this service.