Epson 7000 사용자 설명서
EPSON Stylus Pro 7000
Revision B
Adjustment
Self-Diagnostic Mode Menus
176
ADJ CAP POSITION
Use this function to check the actual capping position and correct the capping
position parameter in the firmware if necessary.
position parameter in the firmware if necessary.
There may be very small differences between printers. Although the
difference may only be a few pulses closer or further on the linear encoder,
this is necessary to correct for any differences between one mechanism and
another.
difference may only be a few pulses closer or further on the linear encoder,
this is necessary to correct for any differences between one mechanism and
another.
1.
Make sure "Adj Cap Position" appears on the LCD and press the Enter
button.
button.
2.
The printer begins the HP detection sequence and automatically detects
the capping position, adjusting the logical position if necessary.
the capping position, adjusting the logical position if necessary.
3.
After the adjustment process is finished, the detected distance between
the HP and the capping position is displayed.
the HP and the capping position is displayed.
4.
Do one of the following:
> Press the Enter button to update the capping position parameter and
proceed to the next menu item, or
> Press the Pause button to avoid updating the capping position
parameter and return to the beginning; “Adj Cap Position” appears on the
LCD
> Press the Enter button to update the capping position parameter and
proceed to the next menu item, or
> Press the Pause button to avoid updating the capping position
parameter and return to the beginning; “Adj Cap Position” appears on the
LCD
Figure 5-14. Cap Position Check Operation
ADJ CHECK SKEW
When the band turns a predetermined amount (during printing), the printer
detects the paper edge using the P EDGE sensor. This value is compared to
the originally detected value for the paper-edge position to determine if the
paper is feeding at a slant.
detects the paper edge using the P EDGE sensor. This value is compared to
the originally detected value for the paper-edge position to determine if the
paper is feeding at a slant.
Any change you make to the Check Skew distance only affects service-related
printouts; the skew-check operation for user printouts does not change.
printouts; the skew-check operation for user printouts does not change.
1.
Make sure "Adj: Check Skew" appears on the LCD and press the Enter
button.
button.
2.
If the paper is not loaded correctly, "Reload Paper" appears indicating you
need to properly load the paper. If the paper is set correctly, the printer
initializes the paper.
need to properly load the paper. If the paper is set correctly, the printer
initializes the paper.
3.
After paper is loaded and initialized, "Check Skew 1.0m" appears. Use
the Paper Feed + and Paper Feed - buttons to adjust the paper-skew
detection distance, then press Enter to begin the skew check.
the Paper Feed + and Paper Feed - buttons to adjust the paper-skew
detection distance, then press Enter to begin the skew check.
4.
After the skew is correctly detected, "Skew Result: xxxx" appears. Press
Enter to proceed to the next menu item, or press Pause to return to the
beginning; “Adj: Check Skew” appears on the LCD.
Enter to proceed to the next menu item, or press Pause to return to the
beginning; “Adj: Check Skew” appears on the LCD.
Figure 5-15. Skew Check Operation
Detecting Origin
After detecting the
HP, the printer
automatically
detects the cap
position
Detecting Cap Position
Position: -0.2500mm
Carriage moves to capping position, and
position appears on LCD.
position appears on LCD.
Please Set Paper
Paper initializes
Check Skew 1.0m
Press [Enter]
Press Paper Feed [+]
or [-] to change the
skew-check distance
(0.1m increments)
Exc. Skew
Paper edges detected
Skew Result:+1.234m
+ xxx = paper skews
to the HP side
- xxx = paper skews
away from the HP
side