Maytag mmv4203d 사용자 설명서

5. With the support tabs facing forward (see illustrations in 

“Locate Wall Stud(s)” section, align the mounting plate center 
marker to the centerline on the wall, making sure its top edge 
is aligned with the horizontal line drawn in Step 3. Make sure 
the mounting plate is level.

6. Through the mounting plate, mark a hole at each end of the 

mounting plate. These are the mounting holes.

7. Holding the mounting plate in place, and making sure it is 

aligned with the top edge line, centerline and the mounting 
holes, find the wall stud centerline(s) drawn in Step 2 of 
“Locate Wall Stud(s).” Mark at least 1, preferably 2 hole(s) 
through the mounting plate, closest to the wall stud 
centerline(s). See illustrations in “Locate Wall Stud(s)” section. 
The blackened holes in the shaded areas are ideal hole 
locations.

8. Set the mounting plate aside.

9. Mark the centerline 3/8" (1 cm) down from the bottom edge of 

the upper cabinet.

10. Using measuring tape, measure out 6" (15.2 cm) on both sides 

of the centerline, and mark.

11. Measure down 4" (10.2 cm) from the mark made in Step 9, 

and mark.

12. Using a straightedge, draw the 2 horizontal, level lines through 

the marks made in steps 9 and11.

13. Draw the 2 vertical, plumb lines down from the marks made in 

Step 7 to complete the 12" x 4" (30.5 x 10.2 cm) rectangle. 
This is the venting cutout area.

14. Cut a 3/4" (19 mm) hole in one corner of the cutout area.
15. Using a keyhole saw, cut out the venting cutout area.

In addition to being installed on at least 1 wall stud, the mounting 
plate must attach to the wall through mounting holes on both 
ends. If the mounting holes are not over wall studs, use two 3/16-
20 x 3" hex-head bolts with toggle nuts. If 1 hole is over a wall 
stud, use 1 lag screw and one 3/16-20 x 3" hex-head bolt with 
toggle nut. If both end mounting holes are over wall studs, use 
2 lag  screws.
1. Drill 5/8" (16 mm) hole(s) through the wall at holes marked for 

3/16-20 x 3" hex-head bolt(s) with toggle nut(s).

2. Drill 1/8" (3 mm) hole(s) into the wall stud(s) at the hole(s) 

marked in Step 7 of “Mark Rear Wall.” Refer to illustrations in 
“Possible Wall Stud Configurations” in “Locate Wall Stud(s)” 
section.

NOTE: Secure the mounting plate to the wall at both end 
mounting holes drilled into the wall studs and/or drywall using 
either 3/16-20 x 3" hex-head bolts with toggle nuts or 3/16 x 2" 
lag screws.
Refer to illustrations in “Locate Wall Stud(s)” section.
1. With the support tabs of the mounting plate facing forward, 

insert 3/16-20 x 3" hex-head bolt(s) through end mounting 
hole(s) that is(are) not over wall stud(s). Start toggle nut(s) on 
bolt(s) from the back of the mounting plate. Leave enough 
space for the toggle nut(s) to go through the wall and to open.

2. Position mounting plate on the wall.
3. Push the bolt(s) with toggle nut(s) through the drywall, and 

finger tighten the bolt(s) to make sure toggle nut(s) has(have) 
opened against drywall.

4. Insert lag screw(s) into the hole(s) drilled into wall stud(s) in 

Step 2 of “Drill Holes in Rear Wall.”

5. Check alignment of mounting plate, making sure it is level.
6. Securely tighten all lag screws and bolts.

C

A

B

A

B

C

D