Cisco Cisco Aironet 1200 Access Point 릴리즈 노트
14
Release Notes for Cisco Aironet Access Points for Cisco IOS Release 12.3(8)JEC
OL-14518-01
Important Notes
Radio MAC Address Appears in ACU
When a Cisco Aironet client device associates to an access point running IOS software, the access point
MAC address that appears on the Status page in the Aironet Client Utility (ACU) is the MAC address
for the access point radio. The MAC address for the access point Ethernet port is on the label on the back
of the access point.
MAC address that appears on the Status page in the Aironet Client Utility (ACU) is the MAC address
for the access point radio. The MAC address for the access point Ethernet port is on the label on the back
of the access point.
Radio MAC Address Appears in Access Point Event Log
When a client device roams from an access point (such as access point alpha) to another access point
(access point bravo), a message appears in the event log on access point alpha stating that the client
roamed to access point bravo. The MAC address that appears in the event message is the MAC address
for the radio in access point bravo. The MAC address for the access point Ethernet port is printed on the
label on the back of the access point.
(access point bravo), a message appears in the event log on access point alpha stating that the client
roamed to access point bravo. The MAC address that appears in the event message is the MAC address
for the radio in access point bravo. The MAC address for the access point Ethernet port is printed on the
label on the back of the access point.
Mask Field on IP Filters Page Behaves the Same As in CLI
In Cisco IOS Release 12.2(8)JA and later, the mask that you enter in the Mask field on the IP Filters page
in the access point GUI behaves the same way as a mask that you enter in the CLI. If you enter
255.255.255.255 as the mask, the access point accepts any IP address. If you enter 0.0.0.0, the access
point looks for an exact match with the IP address that you entered in the IP Address field.
in the access point GUI behaves the same way as a mask that you enter in the CLI. If you enter
255.255.255.255 as the mask, the access point accepts any IP address. If you enter 0.0.0.0, the access
point looks for an exact match with the IP address that you entered in the IP Address field.
Repeater Access Points Running Cisco IOS Software Cannot Associate to
Parent Access Points Running VxWorks
Parent Access Points Running VxWorks
1200 series repeater access points running Cisco IOS software cannot associate to parent access points
that do not run Cisco IOS software (1200 series access points that have not been converted to run Cisco
IOS software).
that do not run Cisco IOS software (1200 series access points that have not been converted to run Cisco
IOS software).
Repeater Access Points Cannot Be Configured as WDS Access Points
Repeater access points can participate in WDS, but they cannot provide WDS. You cannot configure a
repeater access point as a main WDS access point, and if a root access point becomes a repeater in
fallback mode, it cannot provide WDS.
repeater access point as a main WDS access point, and if a root access point becomes a repeater in
fallback mode, it cannot provide WDS.
Crossover Cable Sometimes Needed When Ethernet Speed and Duplex Set to
Fixed on 1100 Series Access Points
Fixed on 1100 Series Access Points
If you change the speed and duplex settings from auto to fixed on an 1100 series access point Ethernet
port, the auto-MDIX feature on the port is disabled. When auto-MDIX is disabled, you must determine
whether to use a straight-through or a crossover cable to connect the access point Ethernet port to another
device. If the Ethernet link goes down after you set the speed and duplex to fixed, try changing the
Ethernet cable from crossover to straight-through or from straight-through to crossover.
port, the auto-MDIX feature on the port is disabled. When auto-MDIX is disabled, you must determine
whether to use a straight-through or a crossover cable to connect the access point Ethernet port to another
device. If the Ethernet link goes down after you set the speed and duplex to fixed, try changing the
Ethernet cable from crossover to straight-through or from straight-through to crossover.