Panasonic WJ-HD200 사용자 설명서
TML
VM*
WR2
Writing error on HDD
Master HDD
Master HDD
Slave HDD
RV2
RV1
HD1
HD2
POW
ERR
Power disconnection due to
electricity failure/trouble has
been detected.
electricity failure/trouble has
been detected.
Thermal error
Temperature exceeds the
operating range.
41
■ System Information
(SYSTEM INFORMATION)
● HDD Hour Meter (HDD HOUR METER)
The meter shows how many hours each hard disk has been
operated in playback, recording and idle. The built-in HDD
needs replacement when the hour meter reads around
30 000 H.
operated in playback, recording and idle. The built-in HDD
needs replacement when the hour meter reads around
30 000 H.
● HDD Capacity (HDD CAPACITY)
The total usable capacity of the built-in hard disk is indicat-
ed.
ed.
● Default (DEFAULT)
This enables the recorder to restore all setup data to the
default values.
default values.
1. Press the JogDial to move the cursor to DEFAULT.
2. When the cursor is on SET
→, press the JogDial again.
3. Select YES or NO with the JogDial, and press the
JogDial.
The default is NO.
The default is NO.
NO: Current setup data is retained.
YES: Current setup data is reset to the default values.
YES: Current setup data is reset to the default values.
When all setup data are reset to the defaults, "SET
DONE" is displayed for a few seconds and then
changes to SET
DONE" is displayed for a few seconds and then
changes to SET
→.
Note: The recorder will restart when the network setup has
been changed and the menu is closed.
● System Version (SYSTEM VERSION)
This line displays the version number of the installed sys-
tem software. You will need the version number when
updating the software.
tem software. You will need the version number when
updating the software.
● System Log (SYSTEM LOG)
The system log is displayed on the monitor with event num-
bers, dates, times, and causes.
bers, dates, times, and causes.
SYSTEM INFORMATION
HDD1 HOUR METER 10000H
HDD2 HOUR METER 10000H
HDD2 HOUR METER 10000H
HDD CAPACITY 228.99G
DEFAULT
DEFAULT
→ SET→
SYSTEM VERSION X.XX
SYSTEM LOG
SYSTEM LOG
O
SYSTEM LOG (1 OF 10)
NO. DATE TIME CAU
99 FEB28.03 6:50:06 WR1
98 FEB28.03 5:23:51 HD1
97 FEB20.03 10:10:23 HD2
96 FEB15.03 23:50:42 RV1
95 FEB11.03 23:52:10 FLL
94 JAN31.03 19:43:32 TML
93 JAN30.03 19:50:14 LS1
92 JAN15.03 19:52:54 FL%
91 JAN10.03 10:40:22 TM4
90 JAN01.03 10:50:20 LS1
NO. DATE TIME CAU
99 FEB28.03 6:50:06 WR1
98 FEB28.03 5:23:51 HD1
97 FEB20.03 10:10:23 HD2
96 FEB15.03 23:50:42 RV1
95 FEB11.03 23:52:10 FLL
94 JAN31.03 19:43:32 TML
93 JAN30.03 19:50:14 LS1
92 JAN15.03 19:52:54 FL%
91 JAN10.03 10:40:22 TM4
90 JAN01.03 10:50:20 LS1
WR1
Writing error
HDD automati-
cally removed
cally removed
Slave HDD
S.M.A.R.T
detects an
error on HDD.
detects an
error on HDD.
HDD XX%
TM*
ALM
Terminal alarm event was
logged, but no picture
recorded. * = 1-8
logged, but no picture
recorded. * = 1-8
VMD
VMD event was logged, but
no picture recorded. * = 1-8
no picture recorded. * = 1-8
LS*
LOSS
Video input loss on channel
# (*). * = 1-8
# (*). * = 1-8
PC*
PC
PC alarm was logged, but
no picture recorded. * = 1-8
no picture recorded. * = 1-8
Power
Error
Errors other than shown
above
above
HDD is FULL.
Warning, HDD is nearing to
the end.
the end.
HDD FULL
FLL
FL%
Abbreviation
Cause
Description