Boss Audio Systems GT-100 사용자 설명서

The limiter attenuates loud input levels to prevent distortion .

Selects the limiter type .

BOSS LIMITER

This selects a stereo limiter .

RACK 160D

This models a dbx 160X .

VTG RACK U

This models a UREI 1178 .

0–100

Adjust this as appropriate for the input 

signal from your guitar . When the input 

signal level exceeds this threshold level, 

limiting will be applied .

1:1–INF:1

This selects the compression ratio used with 

signals in excess of the threshold level .

0–100

Adjusts the volume .

0–100

Adjusts the strength of the picking attack 

when the strings are played . Higher values 

result in s sharper attack, creating a more 

clearly defined sound .

0–100

Adjusts the release time .

This effect distorts the sound to create long sustain .

Refer to “OD/DS TYPE” (p . 5)

*  “CUSTOM” is not available .

0–120

Adjusts the depth of distortion .

-50–+50

Adjusts the tone .

EFFECT LEVEL 0–100

Adjusts the volume of the OD/DS sound .

-50–+50

Adjusts the tone for the low frequency range . 

Turning this to the left (counterclockwise) 

produces a sound with the low end cut; 

turning it to the right boosts the low end in 

the sound .

0–100

Adjusts the volume of the direct sound .

OFF, ON

The tone to one suitable for solos .

0–100

Adjusts the volume level when the Solo Sw 

is ON .

This adjusts the tone as a equalizer . You can adjust the sound quality in ten bands .

-20–+20 dB

-20–+20 dB

Adjusts the tonal quality . You can adjust the sound quality in four bands .

-20–+20 dB

Adjusts the low frequency range tone .

-20–+20 dB

Adjusts the high frequency range tone .

-20–+20 dB

Adjusts the overall volume level of the 

equalizer .

20 Hz–10 .0 kHz

Specifies the center of the frequency range 

that will be adjusted by the LOW-MID GAIN .

0 .5–16

Adjusts the width of the area affected by the 

EQ centered at the LOW-MID FREQ . Higher 

values will narrow the area .

-20–+20 dB

Adjusts the low-middle frequency range 

tone .

20 Hz–10 .0 kHz

Specifies the center of the frequency range 

that will be adjusted by the HIGH-MID GAIN .

0 .5–16

Adjusts the width of the area affected by the 

EQ centered at the HIGH-MID FREQ . Higher 

values will narrow the area .

-20–+20 dB

Adjusts the low-middle frequency range 

tone .

FLAT, 20 Hz–800 Hz

This sets the frequency at which the low 

cut filter begins to take effect . When FLAT is 

selected, the low cut filter will have no effect .

630 Hz–12 .5 kHz, 

FLAT

This sets the frequency at which the high 

cut filter begins to take effect . When FLAT 

is selected, the high cut filter will have no 

effect .

This changes the tone of the connected guitar .

Selects the type of tone modification .

FAT

Fat tone with boosted mid range .

PRES (PRESENCE)

Bright tone with boosted high-mid range .

MILD

Mild tone with the high end cut back .

TIGHT

Tone with the low frequencies cut .

ENHANC (ENHANCE) Tone with the high frequencies boosted .

RESO 1–3  

(RESONATOR 1–3)

This produces a tone with greater power 

and punch by adding resonance in the 

low-frequency range and midrange .

-50–+50

Adjusts the tone for the low frequency 

range .

-50–+50

Adjusts the tone for the High frequency 

range .

0–100

Adjusts the volume of the effect sound .

0–100

This adjusts the strength of the low-end and 

midrange resonance when TYPE is set to 

RESO 1, 2, or 3 .