Marmitek A/V transmitters Wireless: TV Anywhere 09617 사용자 설명서
제품 코드
09617
E
N
G
LI
S
H
13
TV Anywhere™
1. Make sure your device is switched on.
2. Press and hold SETUP [7] until the LED indicator stays lit. Release SETUP.
3. Press the mode button [3] that matches the device you want to control (for example TV).
4. Press Prog+ [5] repeatedly until the channel changes. If you step past the correct code, use
2. Press and hold SETUP [7] until the LED indicator stays lit. Release SETUP.
3. Press the mode button [3] that matches the device you want to control (for example TV).
4. Press Prog+ [5] repeatedly until the channel changes. If you step past the correct code, use
Prog- [5] to go back to the right code.
5. When the device you want to control reacts, press ENT [11] to confirm the code.
!
If your equipment does not have Prog+, you can use PLAY (VCR or DVD) [19] or
POWER [1]. The search starts after the last registered code. Note: if certain functions
of your equipment cannot be controlled, you will have to find a different code for
your brand.
of your equipment cannot be controlled, you will have to find a different code for
your brand.
5.6 Identifying codes found
If the batteries have been outside the remote control for a longer period, the programmed
codes may be erased from the memory. It is a good idea to write down the codes, so you can
reprogram the remote control quickly. If you don’t know the code (for example because you
found the code by autosearch), you can identify it as follows:
1. Press and hold SETUP [7] until the LED indicator [2] stays lit. Release SETUP.
2. Press the mode button [3] for the device you want to identify (VCR, DVD, ASAT or DSAT).
If the batteries have been outside the remote control for a longer period, the programmed
codes may be erased from the memory. It is a good idea to write down the codes, so you can
reprogram the remote control quickly. If you don’t know the code (for example because you
found the code by autosearch), you can identify it as follows:
1. Press and hold SETUP [7] until the LED indicator [2] stays lit. Release SETUP.
2. Press the mode button [3] for the device you want to identify (VCR, DVD, ASAT or DSAT).
The LED will flash once.
3. Press SETUP again. The LED will flash once. To identify the first digit, press each number
button from 0-9 [9] until the LED flashes. The number you pressed, is the first digit of the
code.
code.
5. Press each number key from 0-9 as above to find the second digit.
6. Press each number key from 0-9 as above to find the third digit.
7. Press all digit keys again to locate the fourth digit. As soon as the fourth digit is located,
6. Press each number key from 0-9 as above to find the third digit.
7. Press all digit keys again to locate the fourth digit. As soon as the fourth digit is located,
the LED goes off.
5.7 Configure volume control for various devices
The remote control is preset so that the Volume and Mute keys operate the device which is
programmed by the device keys [3]. If the programmed device does not have a volume/ mute
function then the TV volume will be controlled without having to switch to the TV function.
You can also adjust this set up manually and assign the volume control of the device in
question to the TV, for example, so you adjust the TV volume but not that of, for example,
the set top box, and all this without having to switch to the TV function.
Note, if you perform the procedure below for devices that do not have a volume/ mute
function then the Volume and Mute keys will not work. It is then necessary to switch to the
TV function in order to adjust the volume.
The remote control is preset so that the Volume and Mute keys operate the device which is
programmed by the device keys [3]. If the programmed device does not have a volume/ mute
function then the TV volume will be controlled without having to switch to the TV function.
You can also adjust this set up manually and assign the volume control of the device in
question to the TV, for example, so you adjust the TV volume but not that of, for example,
the set top box, and all this without having to switch to the TV function.
Note, if you perform the procedure below for devices that do not have a volume/ mute
function then the Volume and Mute keys will not work. It is then necessary to switch to the
TV function in order to adjust the volume.
Configuration of one general volume control for all devices operated by the remote
control, e.g. TV:
1. Press SETUP (7) and hold this key down until the LED stays on (takes about 2-3 seconds).
2. Press MUTE (4) and hold this key down until the LED goes off.
3. Briefly press the desired key (3) e.g. TV, the LED flashes and stays on.
control, e.g. TV:
1. Press SETUP (7) and hold this key down until the LED stays on (takes about 2-3 seconds).
2. Press MUTE (4) and hold this key down until the LED goes off.
3. Briefly press the desired key (3) e.g. TV, the LED flashes and stays on.