Marmitek A/V transmitters Wireless: TV Anywhere 09617 사용자 설명서
제품 코드
09617
1
© MARMITEK
4. Briefly press MUTE (4), the LED goes off. The LED will flash quickly for approximately 3
seconds if the selected code does not have a volume/mute function.
5. In this instance, the TV volume will be controlled by all selection keys (3).
Configuration of the volume/mute function for each device individually:
1. Press SETUP (7) and hold this key down until the LED stays on (takes about 2-3 seconds).
2. Press MUTE (4) and hold this key down until the LED goes off.
3. Briefly press the desired key (3) e.g. TV, DVD etc., the LED flashes and stays on.
4. Briefly press the VOLUME key (6, lower volume), the LED flashes and stays on.
5. Briefly press MUTE (4), the LED goes off.
6. The selected device will now operate with its own volume function.
1. Press SETUP (7) and hold this key down until the LED stays on (takes about 2-3 seconds).
2. Press MUTE (4) and hold this key down until the LED goes off.
3. Briefly press the desired key (3) e.g. TV, DVD etc., the LED flashes and stays on.
4. Briefly press the VOLUME key (6, lower volume), the LED flashes and stays on.
5. Briefly press MUTE (4), the LED goes off.
6. The selected device will now operate with its own volume function.
Restoring the volume/mute function to the standard (factory) settings:
1. Press SETUP (7) and hold this key down until the LED stays on (takes about 2-3 seconds).
2. Press MUTE (4) and hold this key down until the LED goes off (the LED now flashes).
3. Press MUTE (4) one more time and the LED goes off.
4. The volume/mute function is restored to the factory settings.
1. Press SETUP (7) and hold this key down until the LED stays on (takes about 2-3 seconds).
2. Press MUTE (4) and hold this key down until the LED goes off (the LED now flashes).
3. Press MUTE (4) one more time and the LED goes off.
4. The volume/mute function is restored to the factory settings.
5.8 Switching between antenna signal and audio/video source
You can connect not only an antenna signal to the TV Anywhere transmitter, but also an
external audio/video source (for example a DVD player, a video recorder or a satellite receiver).
You can then use the TV Anywhere remote control to switch between the antenna signal and
the external source. You do this by pressing the [CATV/ AV] button on the remote control.
Make sure the remote is in CBL mode (press CBL first).
You can connect not only an antenna signal to the TV Anywhere transmitter, but also an
external audio/video source (for example a DVD player, a video recorder or a satellite receiver).
You can then use the TV Anywhere remote control to switch between the antenna signal and
the external source. You do this by pressing the [CATV/ AV] button on the remote control.
Make sure the remote is in CBL mode (press CBL first).
5.9 Changing the code of the 6in1 remote for use with the TV Anywhere
! You only have to change the code of the 6in1 remote if another TV Anywhere system is
used in your immediate neighbourhood (within 100 meters).
! You can only access the screen below / change the handset code AFTER you programmed
the TV Anywhere .
used in your immediate neighbourhood (within 100 meters).
! You can only access the screen below / change the handset code AFTER you programmed
the TV Anywhere .
The default setting of the remote is “0636”. To change the code of both the 6in1 remote and
your TV Anywhere system:
1. Press and hold SETUP until the LED stays lit.
2. Press CBL.
3. Enter one of the following codes:
your TV Anywhere system:
1. Press and hold SETUP until the LED stays lit.
2. Press CBL.
3. Enter one of the following codes:
0639
0638
0637
0636 (default)
4. Switch the TV Anywhere transmitter off and then on again (by using the ON/OFF switch
[7])