Hunter Fan 42737-01 Manual Do Utilizador
6
Hunter Fan Company
42737-01 • 11/14/06
7
42737-01 • 11/14/06
Hunter Fan Company
All wiring must be in accordance with national and local electrical
codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a
qualifi ed electrician.
codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a
qualifi ed electrician.
Wall switches are not included. Select an acceptable general-use switch
in accordance with national and local electrical codes.
in accordance with national and local electrical codes.
4-1. Make sure the power to the outlet box and associated wall switch
location is still OFF.
4-2. To connect the wires, hold the bare metal leads together and place
a wire nut over them, then twist the wire nut clockwise until tight.
4-3. Connect the bare or green ground wired (grounded) from the
ceiling to the green ground wire (grounded) from the ceiling plate
and the green ground wire from the fan.
and the green ground wire from the fan.
4-4. Connect the white wire (ungrounded) from the ceiling to the
white wired (ungrounded) from the fan.
4-5. Connect the remaining wires as follows:
Single Switch Wiring:
• Th
e black wire from the ceiling to the black and the black/
white wire from the fan.
Dual
Switch
Wiring:
• Th
e black wire from the ceiling to the black wire from the fan.
• Th
e black/white wire from the fan to the wire for the wall
switch.
CAUTION: Be sure no bare wire or wire strands are visible after
making connections.
4-6
Turn the splices upward and push them carefully back through the
ceiling plate into the outlet box.
4-7 Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the
outlet box.
outlet box.
3 • Assembling and Hanging the Fan
4 • Wiring the Fan
You can assemble your fan for standard mounting (steps 3-1 – 3-2)
or for low profi le mounting (steps 3-3 – 3-4). Note: For low profi le
mounting, the downrod is replaced with the low profi le washer.
or for low profi le mounting (steps 3-3 – 3-4). Note: For low profi le
mounting, the downrod is replaced with the low profi le washer.
3-1. To assemble fan to hang down from a fl at or angled ceiling, insert
the downrod through the canopy and canopy trim ring. Feed the
wires from the fan through the downrod.
wires from the fan through the downrod.
3-2. Loosen the allen head set screw on the adapter using the large
allen wrench. Screw the pipe and ball assembly into the fan
assembly. Note: When the pipe and ball assembly is fully installed,
2-3 threads on the pipe will still be visible; this is normal. Securely
retighten the set screw with a wrench or pliers. Skip to Step 3-5.
assembly. Note: When the pipe and ball assembly is fully installed,
2-3 threads on the pipe will still be visible; this is normal. Securely
retighten the set screw with a wrench or pliers. Skip to Step 3-5.
CAUTION: Th
e adapter has a special coating on the threads. Do
not remove this coating; the coating prevents the downrod from
unscrewing. Once assembled, do not remove the downrod.
unscrewing. Once assembled, do not remove the downrod.
3-3. Place the low profi le washer (lip up) into the canopy. Be sure the
green ground wire is pointing up toward the ceiling.
3-4. Align the holes in the washer with the holes in the adapter.
Assemble securely with three #8-32 x 3/4” screws.
3-5. Raise the fan and place the hook on the ceiling plate through the
U-shaped hole in the rim.
WARNING: Fan may fall if not assembled as directed in these
installation instructions.
Steps 3-3 – 3-4
#8-32 x 3/4” Screw
Low Profi le Washer
Steps 3-1 – 3-2
Downrod
Canopy
Canopy
Trim Ring
Trim Ring
Set Screw
Step 3-5
U-shaped
Hole
Wire Nut
Step 4-3
Step 4-4