Manualsbrain.com
  1. Manuais
  2. Marcas
  3. ONKYO
  4. TX-SR876
  5. Manual Do Utilizador

ONKYO TX-SR876 Manual Do Utilizador

Download
Página de 150
96
5
Use the Up and Down [
q]/[w] but-
tons to select “Subwoofer”, and 
then use the Left and Right 
[
e]/[r] buttons to select:
Yes: Select if a subwoofer is con-
nected.
No: Select if no subwoofer is con-
nected.
Note:
The same setting is used for Speakers A 
and Speakers B.
6
Use the Up and Down [
q]/[w] but-
tons to select “Front”, and then 
use the Left and Right [
e]/[r] 
buttons to select a crossover fre-
quency.
Notes:
• This setting can be set independently 
for front Speakers A and front 
Speakers B.
• Fixed at “Full Band” if “Subwoofer” 
(step 5) is set to “No”.
7
Use the Up and Down [
q]/[w] but-
tons to select “Center”, and then 
use the Left and Right [
e]/[r] 
buttons to select a crossover fre-
quency.
If no center speaker is connected, select 
None.
Notes:
• The same setting is used for Speakers 
A and Speakers B.
• Can be set if the currently selected 
speakers (Speakers A or Speakers B) 
is set to “BTL” (page 61).
• Cannot select “Full Band” if “Front” 
(step 6) is set to anything other than 
“Full Band”.
• For Speakers B, if any channel is set 
to “Full Band”, “Center” is fixed at 
“Full Band”.
8
Use the Up and Down [
q]/[w] but-
tons to select “Surround”, and 
then use the Left and Right 
[
e]/[r] buttons to select a cross-
over frequency.
If no surround left and right speakers 
are connected, select “None”.
Notes:
• The same setting is used for Speakers 
A and Speakers B.
• Can be set if the currently selected 
speakers (Speakers A or Speakers B) 
is set to “BTL” (page 61).
• Cannot select “Full Band” if “Front” 
(step 6) is set to anything other than 
“Full Band”.
9
Use the Up and Down [
q]/[w] but-
tons to select “SurrBack”, and 
then use the Left and Right 
[
e]/[r] buttons to select a cross-
over frequency.
If no surround back speakers are con-
nected, select “None”.
Notes:
• The same setting is used for Speakers 
A and Speakers B.
• Cannot be set if “Speaker Type: 
Front(Speaker A) or Front(Speaker 
B)” is set to “Bi-Amp” or “BTL” 
(page 61), “Surround” is set to 
“None” (step 8), or “Powered 
Zone2” is being used (page 132).
• Cannot select “Full Band” if “Sur-
round” (step 8) is set to anything 
other than “Full Band”.
10
Use the Up and Down [
q]/[w] but-
tons to select “SurrBack Ch”, 
and then use the Left and Right 
[
e]/[r] buttons to select:
1ch:  Select if one surround back 
speaker is connected.
2ch:  Select if two (left and right) 
surround back speakers are 
connected.
Notes:
• The same setting is used for Speakers 
A and Speakers B.
• Cannot be set if “Speaker Type: 
Front(Speaker A) or Front(Speaker 
B)” is set to “Bi-Amp” or “BTL” 
(page 61), “SurrBack” is set to 
“None” (step 9), or “Powered 
Zone2” is being used (page 132).
Continue with step 11 on the next page.