ONKYO HT-R990 Manual Do Utilizador
![ONKYO](https://files.manualsbrain.com/attachments/8aea18be949e459a0f55b8379882c4c18cf8698b/common/fit/150/50/cdcf544ed9e39671a87280176f4bdeefe94b330d63641d63ea2dc47d350c/brand_logo.png)
45
En
Level Calibration
Here you can adjust the level of each speaker with the
built-in test tone so that the volume of each speaker is the
same at the listening position.
built-in test tone so that the volume of each speaker is the
same at the listening position.
■
Left, Front High Left, Center
*1
, Front High Right,
Right, Surround Right, Surround Back Right,
Surround Back Left, Surround Left
Surround Back Left, Surround Left
`
–12dB to 0dB to +12dB in 1 dB steps.
■
Subwoofer
*1
`
–15dB to 0dB to +12dB in 1 dB steps.
Note
• These settings cannot be calibrated in either of the following
cases:
– a pair of headphones is connected.
– the “Audio TV Out” setting is set to “On” (
– a pair of headphones is connected.
– the “Audio TV Out” setting is set to “On” (
page 55).
– “HDMI Control(RIHD)” is set to “On” (
page 54) and
you’re listening through your TV speakers.
– the AV receiver is muted.
• Speakers that you set to “No” in the “Speaker Configuration”
cannot be selected (
page 44).
• The test tone is output at the standard level for THX, which is
0 dB (absolute volume setting 82). If you normally listen at
volume settings below this, be careful because the test tone will
be much louder.
volume settings below this, be careful because the test tone will
be much louder.
*1
For the center speaker and subwoofer, the level settings made
by using the Home menu are saved in this menu
(
by using the Home menu are saved in this menu
(
page 39).
Tip
• If you’re using a handheld sound level meter, adjust the level of
each speaker so that it reads 75 dB SPL at the listening position,
measured with C-weighting and slow reading.
measured with C-weighting and slow reading.
Equalizer Settings
With the Equalizer settings, you can adjust the tone of
speakers individually with a 5-band equalizer. The volume
of each speaker can be set.
speakers individually with a 5-band equalizer. The volume
of each speaker can be set.
■
Equalizer
`
Manual:
You can adjust the equalizer for each speaker
manually. Continue with the following procedure:
manually. Continue with the following procedure:
`
Off
:
Tone off, response flat.
Note
• You can select: “63Hz”, “250Hz”, “1000Hz”, “4000Hz”, or
“16000Hz”. And for the subwoofer, “25Hz”, “40Hz”, “63Hz”,
“100Hz”, or “160Hz”.
“100Hz”, or “160Hz”.
• When the Direct listening mode is selected, the equalizer
settings have no effect.
• If “Audyssey” is enabled, it prevails over this setting
page 48).
This setting is set automatically by Audyssey 2EQ
Room Correction and Speaker Setup (
Room Correction and Speaker Setup (
page 30).
Adjust the level control of the subwoofer to the THX
POSITION before calibrating this system.
POSITION before calibrating this system.
1
Press
w to select “Channel”, and then use
e/r to select a speaker.
2
Use
q/w to select a frequency, and then use
the
e/r to adjust the level at that frequency.
The volume at each frequency can be adjusted
from –6dB to 0dB to +6dB in 1 dB steps.
from –6dB to 0dB to +6dB in 1 dB steps.
Tip
• Low frequencies (e.g., 63Hz) affect bass sounds;
high frequencies (e.g., 16000Hz) affect treble
sounds.
sounds.
3
Use
q to select “Channel”, and then use e/r
to select another speaker.
Repeat steps 1 and 2 for each speaker.
You cannot select speakers that you set to “No”
in the “Speaker Configuration” (
Repeat steps 1 and 2 for each speaker.
You cannot select speakers that you set to “No”
in the “Speaker Configuration” (
page 44).