Ariens 936036-2548 Manual Do Utilizador
GB - 11
MOVING THE UNIT MANUALLY
IMPORTANT: DO NOT push or pull (tow) tractor with
another vehicle. Transmission damage will occur. Use
truck or trailer when transporting.
another vehicle. Transmission damage will occur. Use
truck or trailer when transporting.
1. Stop engine.
2. Pull bypass lever rearward and lock in slot to
disengage transmission.
3. Release parking brake.
4. Push unit to desired location.
5. Apply parking brake.
6. Pull lever out of slot and slowly release forward to
engage transmission.
Ariens Dealers will provide any service or adjustments
which may be required to keep your unit operating at
peak efficiency. Should engine service be required,
contact an Ariens dealer or an authorized engine
manufacturer's service center.
which may be required to keep your unit operating at
peak efficiency. Should engine service be required,
contact an Ariens dealer or an authorized engine
manufacturer's service center.
SERVICE POSITION
Place unit on a flat level surface. Stop engine and
disengage clutches. Assure unit is secure and will not tip
over. Strap and clamp onto lift if used. Open hood to
access battery or engine.
disengage clutches. Assure unit is secure and will not tip
over. Strap and clamp onto lift if used. Open hood to
access battery or engine.
MAINTENANCE SCHEDULE
The chart below shows recommended maintenance.
More frequent service may be required due to working
conditions (heavy loads, high ambient temperatures,
dusty conditions, or airborne debris).
More frequent service may be required due to working
conditions (heavy loads, high ambient temperatures,
dusty conditions, or airborne debris).
*
Change after first 5 to 8 hours of use.
** For all engine maintenance information, refer to engine
manual.
CHECK SAFETY INTERLOCK SYSTEM
See Filling Fuel Tank on page 10.
CHECK PARKING BRAKE
The parking brake is designed to prevent unexpected
movement of the unit. If the parking brake allows unit
movement while engaged for proper parking brake spring
setting (see Parking Brake Spring on page 15).
movement of the unit. If the parking brake allows unit
movement while engaged for proper parking brake spring
setting (see Parking Brake Spring on page 15).
CHECK FASTENERS
Be certain all hardware is tightened to the proper torque.
Pay special attention to blades, guards and safety
shields.
Pay special attention to blades, guards and safety
shields.
TIRE PRESSURE
Check air pressure in all tires every 25 operating hours
(see Specifications on page 18).
(see Specifications on page 18).
BATTERY
Clean Battery
Keep battery and its terminals clean. Inspect every 25
operating hours or monthly for best performance.
operating hours or monthly for best performance.
1. Disconnect cables from battery (negative, then
positive).
2. Clean terminals and battery cable ends with wire
brush.
3. Coat terminals with grease or petroleum jelly.
4. Reconnect cables to battery (positive, then
negative).
MAINTENANCE
WARNING: AVOID INJURY. Read and
understand the entire Safety section before
proceeding.
understand the entire Safety section before
proceeding.
MAINTENANCE SCHEDULE
Service Performed
Before
Each
Use
Every
25 hrs.
Every
50 hrs.
Check Safety Interlock
System
System
•
Check Parking Brake
•
Check Fasteners
•
Check Engine Oil**
•
Change Engine Oil**
•*
Tire Pressure
•
Battery
•
Mower Blades
•
General Lubrication
•
WARNING: FAILURE OF INTERLOCK,
together with improper operation could result in
death or serious injury.
together with improper operation could result in
death or serious injury.
WARNING: AVOID INJURY. Read and
understand the entire Safety section before
proceeding.
understand the entire Safety section before
proceeding.
WARNING: Battery posts, terminals and related
accessories contain lead and lead compounds,
chemicals known to the State of California to
cause cancer and reproductive harm. Wash
hands after handling.
accessories contain lead and lead compounds,
chemicals known to the State of California to
cause cancer and reproductive harm. Wash
hands after handling.