Toshiba E6581830 Manual Do Utilizador

 

E658130 

- 21 - 

1. Output signals (Master -> Inverter) 

The output signals from the master unit are indicated. (Input signals to inverter) 

Device No. 

Signal 

Description 

RYn0 

Forward run command 

OFF: Stop command ON: Forward run command*** 

RYn1 

Reverse run command 

OFF: Stop command ON: Reverse run command*** 

RYn2 

Input terminal function 3(S1) 

The function depends on input terminal selection 3 (c142) *

RYn3 

Input terminal function 4(S2) 

The function depends on input terminal selection 4 (c143) *

RYn4 

Input terminal function 5(S3) 

The function depends on input terminal selection 5 (c144) *

RYn5 

Input terminal function 6(S4) 

The function depends on input terminal selection 6 (c145) *

RYn6 

Input terminal function (PIOFF) 

The function depends on input terminal selection 7 (c146) *

RYn7 

Input terminal function 8(AD1) 

The function depends on input terminal selection 8 (c147) *

RYn8 

Input terminal function 9(ESTP) 

The function depends on input terminal selection 9 (c148) *

RYn9 

Intercept output to inverter   
(Coast stop) 

Stop the output of the inverter when turned on this signal.   
(Stop the output in the secondary circuit) 

RYnA 

Frequency priority CC-Link 

Speed commands are entered from the CC-Link. 

RYnB 

Command priority CC-Link 

Signals from the CC-Link are used to start and stop operation

RYnC 

Monitor command 

When the monitor command (RYnC) is switched on,    each   
monitored values are set to remote registers RWrn, RWrn+1, 
RWrn+4 to RWrn+7 and monitoring flag (RXnC) switches on.
While the monitor command (RYnC) is on, the monitored   
value is always updated. 

RYnD 

Frequency setting command   
(RAM) 

When the frequency setting command (RYnD) is switched 
on, the set frequency RWwn+1 is written to the inverter.   
After the writing completion, frequency setting completion flag 
(RXnD) switches on. 
When the frequency setting command (RYnD) is ON, the set 
frequency is always updated.   

RYnE Reserved** 

Reserved** 

RYnF 

Instruction code execution request

When the instruction code execution request (RYnF) is   
switched on, processes corresponding to the instruction codes 
are set to RWwn+2, RWwn+10, RWwn+12, RWwn+14,   
RWwn+16 and RWwn+18 are executed. 
After completion of instruction code execution, instruction code 
execution completion flag (RXnF) switches on. 
When an instruction code execution error occurs, a value other 
than 0 is set to the reply code (RWrn+2, RWrn+10, RWrn+12, 
RWrn+14, RWrn+16 and RWrn+18) 
The instruction code execution request is effective only when   
this signal changes from OFF to ON. 
Special monitor (72H) is chosen by the instruction code, and 
this signal always updates a monitor value during ON. 

RY(n+1)0 

to Y(n+1)9 

Reserved** Reserved** 

RY(n+1)A  Error reset request 

If the error reset request (RY(n+1)A) is switched on only   
when an inverter fault occurs, the inverter is reset and the  
error status flag (RX(n+1)A) switches off. 

RY(n+1)B 

to RY(n+1)F 

Reserved** Reserved** 

"n" is depend on the station number. 
*    The input terminal function can be changed by the input terminal function selections(

c142

 to c148

). 

 

(But there are functional restrictions. Refer to the following page.) 

** Set OFF (“0”) to reserved bit. 

***When RYn0 and RYn1 are ON simultaneously, the rotation is followed a parameter f105(default = stop).